- 您現在的位置：買賣IC網 > PDF目錄372109 > SAA3010 (NXP Semiconductors N.V.) Infrared remote control transmitter RC-5 PDF資料下載
參數資料
| 型號： | SAA3010 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Infrared remote control transmitter RC-5 |
| 中文描述： | 紅外遙控器遙控- 5 |
| 文件頁數： | 6/20頁 |
| 文件大?。?/td> | 94K |
| 代理商： | SAA3010 |
June 1989
6
Philips Semiconductors
Product specification
Infrared remote control transmitter RC-5
SAA3010
FUNCTIONAL DESCRIPTION
Keyboard operation
Every connection of one X-input and one DR-output will be recognized as a legal key operation and will cause the device
to generate the corresponding code. The same applies to every connection of one Z-input to one DR-output with the
proviso that SSM must be LOW. When SSM is HIGH a wired connection must exist between a Z-input and a DR-output.
If no connection is present the system number will not be generated. Activating two or more X-inputs, Z-inputs or Z-inputs
and X-inputs at the same time is an illegal action and inhibits further activity (oscillator will not start).
When one X- or Z-input is connected to more than one DR-output, the last scan signal will be considered as legal.
The maximum value of the contact series resistance of the switched keyboard is 7 k
.
Inputs
In the quiescent state the command inputs X0 to X7 are held HIGH by an internal pull-up transistor. When the system
mode selection (SSM) input is LOW and the system is quiescent, the system inputs Z0 to Z3 are also held HIGH by an
internal pull-up transistor. When SSM is HIGH the pull-up transistor for the Z-inputs is switched off, in order to prevent
current flow, and a wired connection in the Z-DR matrix provides the system number.
Outputs
The output signal DATA transmits the generated information in accordance with the format illustrated by Fig.4 and
Tables 1 and 2. The code is transmitted using a biphase technique as illustrated by Fig.5. The code consists of four parts:
Start part
1.5 bits (2
×
logic 1)
Control part
1 bit
System part
5 bits
Command part
6 bits
The output signal MDATA transmits the generated information modulated by 1/12 of the oscillator frequency with a 50%
duty factor.
In the quiescent state both DATA and MDATA are non-conducting (3-state outputs).
The scan driver outputs DR0 to DR7 are open drain n-channel transistors and conduct when the circuit is quiescent.
After a legal key operation the scanning cycle is started and the outputs switched to the conductive state one by one.
The DR-outputs were switched off at the end of the preceding debounce cycle.
相關PDF資料 |
PDF描述 |
|---|---|
| SAA3027 | INFRARED REMOTE CONTROL TRANSMITTER |
| SAA3049AT | Infrared remote control decoder |
| SAA3049 | Infrared remote control decoder |
| SAA3049A | Infrared remote control decoder |
| SAA3049AP | Infrared remote control decoder |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SAA3010T | 制造商:Misc 功能描述: |
| SAA-301100 | 制造商:SII 制造商全稱:Seiko Instruments Inc 功能描述:Single-Mode FC D-Shape ADAPTOR supplied |
| SAA-301200 | 制造商:SII 制造商全稱:Seiko Instruments Inc 功能描述:Single-Mode FC D-Shape ADAPTOR supplied |
| SAA30131004 | 制造商:LG Corporation 功能描述:S/W,Firmware |
| SAA30131907 | 制造商:LG Corporation 功能描述:S/W,Firmware |
發布緊急采購，3分鐘左右您將得到回復。