參數資料
型號： SAA7113
廠商： NXP Semiconductors N.V.
英文描述： GT 14C 14#16 PIN PLUG
中文描述： 9位視頻輸入處理器
文件頁數： 27/80頁
文件大?。?/td> 279K
代理商： SAA7113
1999 Jul 01
27
Philips Semiconductors
Product specification
9-bit video input processor
SAA7113H
Some details about data types:
Active video
(data type 15) component YUV 4 : 2 : 2
signal, 720 active pixels per line. Format and nominal
levels are given in Fig.23 and Table 13.
Test line
(data type 6), is similar to decoded YUV-data
as in active video, with two exceptions:
– vertical filter (chrominance comb filter for NTSC
standards, PAL-phase-error correction) within the
chrominance processing is disabled
– peaking and chrominance trap are bypassed within
the luminance processing, if I
2
C-bus bit VBLB is set.
This data type is defined for future enhancements; it
could be activated for lines containing standard test
signals within the vertical blanking period; currently
the most sources do not contain test lines.
This data type is available only in lines with VREF = 0,
see I
2
C-bus detail section, Table 45.
Format and nominal levels are given in Fig.23 and
Table 13.
Raw samples
(data type 7) oversampled CVBS-signal
for intercast applications; the data rate is 27 MHz.
The horizontal range is programmable via
HSB7 to HSB0, HSS7 to HSS0 and HDEL1 to HDEL0;
see I
2
C-bus section subaddresses 06H, 07H and 10H
and Tables 33, 34 and 46.
Format and nominal levels are given in Fig.24 and
Table 15.
Sliced data
(various standards, data types 0 to 5 and
8 to 14).
The format is given in Table 17.
The data type selections by LCR are overruled by setting
VIPB (subaddress 11H bit 1) to logic 1. This setting is
mainly intended for device production tests. The VPO-bus
carries the upper or lower 8 bits of the two ADCs
depending on the ADLSB (subaddress 13H bit 7) setting.
The output configuration is done via MODE3 to MODE0
settings (subaddress 02H bits 3 to 0, see Table 27). If the
YC-mode is selected, the VPO-bus carries the multiplexed
output signals of both ADCs, in CVBS-mode the output of
only one ADC. No timing reference codes are generated in
this mode.
Note
: The LSBs (bit 0) of the ADCs are available on
pins RTS0 or RTS1. See Chapter 15, subaddress 12H for
details.
The SAV/EAV timing reference codes define start and end
of valid data regions.
Table 5
SAV/EAV format
BIT 7
BIT 6 (F)
BIT 5 (V)
BIT 4 (H)
BIT 3
(P3)
BIT 2
(P2)
BIT 1
(P1)
BIT 0
(P0)
1
field bit
1st field: F = 0;
2nd field: F = 1;
for vertical timing
see Tables 6 and 7
vertical blanking bit
VBI: V = 1;
active video: V = 0;
for vertical timing
see Tables 6 and 7
H = 0 in SAV;
H = 1 in EAV
reserved; evaluation not
recommended (protection
bits according to ITU 656)
The generation of the H-bit and consequently the timing of
SAV/EAV corresponds to the selected data format. H = 0
during active data region. For all data formats excluding
data type 7 (raw data), the length of the active data region
is 1440 LLC. For the YUV 4 : 2 : 2 formats (data
types 15 and 6) every clock cycle within this range
contains valid data, see Table 13.
The sliced data stream (various standards, data types
0 to 5 and 8 to 14; see Table 17) contains also invalid
cycles marked as 00H.
The length of the raw data region (data type 7) is
programmable via HSB7 to HSB0 and HSS7 to HSS0
(subaddresses 06H and 07H; see Fig.24).
During horizontal blanking period between EAV and SAV
the ITU-blanking code sequence ‘-80-10-80-10-...’ is
transmitted.
The position of the F-bit is constant according to ITU 656
(see Tables 6 and 7).
The V-bit can be generated in four different ways
(see Tables 6 and 7) controlled via OFTS1 and OFTS0
(subaddress 10H, bits 7 and 6), VRLN (subaddress 10H,
bit 3) and LCR2 to LCR24 (subaddresses 41H to 57H).
F and V bits change synchronously with the EAV code.
相關PDF資料
PDF描述
SAA7114H PAL/NTSC/SECAM video decoder with adaptive PAL/NTSC comb filter, VBI data slicer and high performance scaler
SAA7114E PAL/NTSC/SECAM video decoder with adaptive PAL/NTSC comb filter, VBI data slicer and high performance scaler
SAA7114 PAL/NTSC/SECAM video decoder with adaptive PAL/NTSC combfilter, VBI-data slicer and high performance scaler
SAA7115 PAL/NTSC/SECAM Video Decoder with Adaptive PAL/NTSC Comb Filter, High Performance Scaler, I2C Sliced Data Readback and SQ PIXEL OUTPUT
SAA7116 Digital Video to PCI Interface
相關代理商/技術參數
參數描述
SAA7113H 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:9-bit video input processor
SAA7113H/V2,518 功能描述:視頻 IC VIDEO INPUT PROCESSOR (V9) RoHS:否 制造商:Fairchild Semiconductor 工作電源電壓:5 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-28 封裝:Reel
SAA7113H/V2,557 功能描述:視頻 IC 9-BIT VIDEO INPUT RoHS:否 制造商:Fairchild Semiconductor 工作電源電壓:5 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-28 封裝:Reel
SAA7113H/V2557 制造商:NXP Semiconductors 功能描述:VIDEO INPUT PROCESSOR 9BIT 44QFP
SAA7113HB 功能描述:視頻 IC 9-BIT VIDEO INPUT PROCESSOR RoHS:否 制造商:Fairchild Semiconductor 工作電源電壓:5 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-28 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*