- 您現在的位置：買賣IC網 > PDF目錄376335 > SAB80C52-P (SIEMENS A G) High-Performance 8-Bit Single Chip Microcontroller PDF資料下載
參數資料
| 型號： | SAB80C52-P |
| 廠商： | SIEMENS A G |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | High-Performance 8-Bit Single Chip Microcontroller |
| 中文描述： | 8-BIT, MROM, 12 MHz, MICROCONTROLLER, PDIP40 |
| 文件頁數： | 33/56頁 |
| 文件大?。?/td> | 668K |
| 代理商： | SAB80C52-P |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁當前第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
SAB 80C515/80C535
Semiconductor Group
32
If all timers are stopped and the A/D converter and the serial interface are not running, the
maximum power reduction can be achieved. This state is also the test condition for the idle
mode
I
CC
(see DC characteristics, note 5).
So the user has to take care which peripheral should continue to run and which has to be
stopped during idle mode. Also the state of all port pins – either the pins controlled by their
latches or controlled by their secondary functions – depends on the status of the controller
when entering idle mode.
Normally the port pins hold the logical state they had at the time idle mode was activated. If
some pins are programmed to serve their alternate functions they still continue to output during
idle mode if the assigned function is on. This applies to the compare outputs as well as to the
clock output signal or to the serial interface in case it cannot finish reception or transmission
during normal operation. The control signals ALE and PSEN hold at logic high levels (see
table 5).
As in normal operation mode, the ports can be used as inputs during idle mode. Thus a capture
or reload operation can be triggered, the timers can be used to count external events, and
external interrupts will be detected.
The idle mode is a useful feature which makes it possible to "freeze" the processor's status –
either for a predefined time, or until an external event reverts the controller to normal operation,
as discussed below. The watchdog timer is the only peripheral which is automatically stopped
during idle mode. If it were not disabled on entering idle mode, the watchdog timer would reset
the controller, thus abandoning the idle mode.
Table 5
Status of External Pins During Idle and Power-Down Mode
Last instruction executed from
internal code memory
Last instruction executed from
external code memory
Outputs
Idle
Power-down
Idle
Power-down
ALE
High
Low
High
Low
PSEN
High
Low
High
Low
PORT 0
Data
Data
Float
Float
PORT 1
Data/alternate
outputs
Data/last
output
Data/alternate
outputs
Data/last
output
PORT 2
Data
Data
Address
Data
PORT 3
Data/alternate
outputs
Data/last
output
Data/alternate
outputs
Data/last
output
PORT 4
Data
Data
Data
Data
PORT 5
Data
Data
Data
Data
相關PDF資料 |
PDF描述 |
|---|---|
| SAB80C535-16-N | 8-Bit CMOS Single-Chip Microcontroller |
| SAB80C535-20-N | 8-Bit CMOS Single-Chip Microcontroller |
| SAB80C535-M | 8-Bit CMOS Single-Chip Microcontroller |
| SAB80C535-N | 8-Bit CMOS Single-Chip Microcontroller |
| SAB80C166-M | 16-Bit CMOS Single-Chip Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SAB80C52-P-T40/85 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:High-Performance 8-Bit Single Chip Microcontroller |
| SAB80C535 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:8-Bit CMOS Single-Chip Microcontroller |
| SAB80C535-16-N | 制造商:Infineon Technologies AG 功能描述:MicroController, 8-Bit, 68 Pin, Plastic, PLCC |
| SAB80C53516N4085 | 制造商:Infineon Technologies AG 功能描述:MCU 8-Bit C500 8051 CISC ROMLess 5V 68-Pin PLCC |
| SAB80C53516N-DA | 制造商:Infineon Technologies AG 功能描述:NOTE: USE SABC515 |
發布緊急采購，3分鐘左右您將得到回復。