![](http://datasheet.mmic.net.cn/180000/SB-36220I6-323_datasheet_11366056/SB-36220I6-323_3.png)
3
Data Device Corporation
www.ddc-web.com
SB-36220IX
L-01/06-0
VALUE
PARAMETER
UNIT
TABLE 1. SB-36220IX SPECIFICATIONS (PER CHAN)
These specifications apply over the rated power supply, temperature, and
reference frequency ranges; 10% signal amplitude variation and 10% har-
monic distortion.
RESOLUTION
ACCURACY
DSC-11520-305
DR-11525-305
DSC-11524-304
ON BOARD
OSCILLATOR
Option P/N
Carrier Frequency
Voltage Range
Drive
SIGNAL OUTPUT
Synchro
Resolver
Resolver (Single Ended)
REFERENCE INPUT
Option P/N
Carrier Frequency
Type (differential)
Voltage (±5%)
Input Impedance
differential (min)
single ended (min)
Common-mode Range
POWER SUPPLY
(NOTE 2)
Voltage
Current
Fully loaded
(1.5VA OSC option
+ 6 Hybrids
DSC-11520/24,
DR-11525)
6 Hybrids only
(DSC-11520/24,
DR-11525)
TEMPERATURE
RANGE
Operating (XIX-3XXX)
Storage
PHYSICAL
CHARACTERISTICS
Size
Weight
in.
mm.
lbs.
Full-size PCI format. Double-width card
when 90 Vrms/115 Vrms required.
12.3 x 4.2 x 0.91
312 x 106.7 x 23.1
1 max, depending on configuration
°C
0 to +70
-40 to +85
Vdc
A max.
+5
4
2
Vrms L-L
Hz
Vrms
Ohms
Vpeak
I0
47 - 7k
diff.
4.4, 26,115
100k
50k
50
I1
400
diff.
26
100k
50k
50
I2
360 - 400
diff.
115
300k
200k
200
11.8
2.0 or 6.8
(See Note 1)
11.8
90
—
Hz
Vrms
mA max.
I4
57 - 7k
0 - 3.4
300
I5
360 - 7k
0 - 26
60
I6
57 - 440
0 - 115
13
47-1KHZ
1 Min.
2 Min.
For frequency higher than 1kHz,
use the DR-11525 and refer to the
converter data sheet specs.
Bits
12 or 16 programmable
Solid State
Transformer Isolated
FIGURE 2. CONTROL PANEL
Easy to use control panel allows position data entry for each
channel. This is ideal for test environments.
FIGURE 3. OPTIONS PANEL
The options panel allows the oscillator to be set for amplitude and
frequency, dynamic rotation and two-speed mode of operation.
SB-3622X SOFTWARE DISPLAY WINDOWS
Solid State
Transformer Isolated
Solid State
Transformer Isolated
I3
60
diff.
115
300k
200k
200
Note 1: S1 and S4 are no connect, because outputs are single ended (common
gnd to common gnd on card).
Note 2 : Requires a 5V PCI card slot, will not operate on a 3.3V PCI slot.
Note 3 : For specific specifications not listed, refer to the specific hybrid type data
sheet. See ordering info to determine hybrid type used.
SOFTWARE
Window GUI example software and DOS console application
example software are included. The provided DDL allows the
user to create custom application software. The software DDL
provides function calls to control resolution, bandwidth, refer-
ence amplitude and reference frequency. This provides access to
angular information and can drive dynamic rotation of the output.
dataSIMS software support available, contact DDC software
applications department for details.
HARDWARE CONFIGURATION
The SB-3622X is a PCI device, and as such does not require any
jumpers or switches to set the Base address or interrupt values.
The job of configuration for Plug-and-Play PCI configuration is
performed by the PC BIOS. During the initial power on boot
process, the BIOS performs an enumeration of the PCI bus and
DYNAMIC
ROTATION
RPS
MIN/MAX
at 12 bit resolution (0.03 to 2014)
at 16 bit resolution (0.03 to 125)