- 您現在的位置：買賣IC網 > PDF目錄379352 > SC16C750BIA44 (NXP Semiconductors N.V.) 5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs PDF資料下載
參數資料
| 型號： | SC16C750BIA44 |
| 廠商： | NXP Semiconductors N.V. |
| 元件分類： | 收發器 |
| 英文描述： | 5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs |
| 封裝： | SC16C750BIA44<SOT187-2 (PLCC44)|<<http://www.nxp.com/packages/SOT187-2.html<1<week 41, 2004,;SC16C750BIA44<SOT187-2 (PLCC44)|<<http://www.nxp.com/packages/SOT187-2.html&l |
| 文件頁數： | 7/44頁 |
| 文件大?。?/td> | 212K |
| 代理商： | SC16C750BIA44 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
SC16C750B_5
NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 05 — 17 October 2008
7 of 44
NXP Semiconductors
SC16C750B
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
RCLK
10
54
4
I
Receiver clock.
RCLK is the 16
×
baud rate clock for the receiver
section of the UART.
Master Reset.
When active (HIGH), RESET clears most UART
registers and sets the levels of various output signals.
Read inputs.
When either IOR or IOR is active (LOW or HIGH,
respectively) while the UART is selected, the CPU is allowed to
read status information or data from a selected UART register. Only
one of these inputs is required for the transfer of data during a read
operation; the other input should be tied to its inactive level (that is,
IOR tied LOW or IOR tied HIGH).
Ring indicator.
RI is a modem status signal. Its condition can be
checked by reading bit 6 (RI) of the Modem Status Register. Bit 2
(
RI) of the MSR indicates that RI has changed from a LOW to a
HIGH level since the last read from the MSR. If the modem status
interrupt is enabled when this transition occurs, an interrupt is
generated.
Request to send.
When active, RTS informs the modem or data
set that the UART is ready to receive data. RTS is set to the active
level by setting the RTS Modem Control Register bit and is set to
the inactive (HIGH) level either as a result of a Master Reset or
during Loopback mode operations or by clearing bit 1 (RTS) of the
MCR. In the auto-RTS mode, RTS is set to the inactive level by the
receiver threshold control logic.
Receiver ready.
Receiver Direct Memory Access (DMA) signaling
is available with RXRDY. When operating in the FIFO mode, one of
two types of DMA signaling can be selected using the FIFO Control
Register bit 3 (FCR[3]). When operating in the 16C450 mode, only
DMA mode 0 is allowed. Mode 0 supports single-transfer DMA in
which a transfer is made between CPU bus cycles. Mode 1
supports multi-transfer DMA in which multiple transfers are made
continuously until the receiver FIFO has been emptied. In DMA
mode 0 (FCR[0] = 0 or FCR[0] = 1, FCR[3] = 0), when there is at
least one character in the receiver FIFO or receiver holding register,
RXRDY is active (LOW). When RXRDY has been active but there
are no characters in the FIFO or holding register, RXRDY goes
inactive (HIGH). In DMA mode 1 (FCR[0] = 1, FCR[3] = 1), when
the trigger level or the time-out has been reached, RXRDY goes
active (LOW); when it has been active but there are no more
characters in the FIFO or holding register, it goes inactive (HIGH).
Serial data input.
RX is serial data input from a connected
communications device.
Serial data output.
TX is composite serial data output to a
connected communication device. TX is set to the marking (HIGH)
level as a result of Master Reset.
RESET
39
32
24
I
IOR
IOR
25
24
10
9
-
14
I
I
RI
43
38
-
I
RTS
36
26
21
O
RXRDY
32
21
19
O
RX
11
55
5
I
TX
13
58
6
O
Table 2.
Symbol
Pin description
…continued
Pin
PLCC44 LQFP64
Type
Description
HVQFN32
相關PDF資料 |
PDF描述 |
|---|---|
| SC16C750BIB64 | 5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs |
| SC16C750BIBS | 5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs |
| SC16C751BIBS | 5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs |
| SC16C752BIB48 | 5 V, 2.2 V and 2.5 V dual UART, 5 Mbit-s (max.), with 64-byte FIFOs |
| SC16C752BIBS | 5 V, 2.2 V and 2.5 V dual UART, 5 Mbit-s (max.), with 64-byte FIFOs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC16C750BIA44,512 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 1CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C750BIA44,518 | 功能描述:UART 接口集成電路 1CH. UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C750BIA44,529 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 1CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C750BIA44-S | 功能描述:UART 接口集成電路 16CB 2.5V-5V 1CH UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C750BIA44-T | 功能描述:UART 接口集成電路 1CH. UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。