- 您現在的位置：買賣IC網 > PDF目錄3764 > SC28L91A1B,551 (NXP Semiconductors)IC UART SINGLE W/FIFO 44-PQFP PDF資料下載
參數資料
| 型號： | SC28L91A1B,551 |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 29/30頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART SINGLE W/FIFO 44-PQFP |
| 產品培訓模塊： | Stand-Alone UARTs |
| 標準包裝： | 96 |
| 系列： | IMPACT |
| 特點： | 故障啟動位檢測 |
| 通道數： | 1，UART |
| FIFO's： | 16 字節 |
| 電源電壓： | 3.3V，5V |
| 帶自動流量控制功能： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 44-QFP |
| 供應商設備封裝： | 44-PQFP（10x10） |
| 包裝： | 管件 |
| 產品目錄頁面： | 828 (CN2011-ZH PDF) |
| 其它名稱： | 568-1187 935267419551 SC28L91A1B-S |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁
Philips Semiconductors
Product data sheet
SC28L91
3.3 V or 5.0 V Universal Asynchronous
Receiver/Transmitter (UART)
2004 Oct 21
8
PIN CONFIGURATION FOR 80XXX BUS INTERFACE (INTEL)
Symbol
Pin
type
Name and function
I/M
I
Bus Configuration: When high or not connected configures the bus interface to the Conditions shown in this table.
D0–D7
I/O
Data Bus: Bi-directional 3-State data bus used to transfer commands, data and status between the UART and the
CPU. D0 is the least significant bit.
CEN
I
Chip Enable: Active-Low input signal. When Low, data transfers between the CPU and the UART are enabled on
D0–D7 as controlled by the WRN, RDN and A0–A3 inputs. When High, places the D0–D7 lines in the 3-State condi-
tion.
WRN
I
Write Strobe: When Low and CEN is also Low, the contents of the data bus is loaded into the addressed register. The
transfer occurs on the rising edge of the signal.
RDN
I
Read Strobe: When Low and CEN is also Low, causes the contents of the addressed register to be presented on the
data bus. The read cycle begins on the falling edge of RDN.
A0–A3
I
Address Inputs: Select the UART internal registers and ports for read/write operations.
RESET
I
Reset: A High level clears internal registers (SR, IMR, ISR, OPR, OPCR), puts OP0–OP7 in the High state, stops the
counter/timer, and puts the Channel in the inactive state, with the TxD outputs in the mark (High) state. Sets MR point-
er to MR1. See Figure 4
INTRN
O
Interrupt Request: Active-Low, open-drain, output which signals the CPU that one or more of the eight maskable in-
terrupting conditions are true. This pin requires a pull-up device.
X1/CLK
I
Crystal 1: Crystal or external clock input. A crystal or clock of the specified limits must be supplied at all times. When a
crystal is used, a capacitor must be connected from this pin to ground (see Figure 11).
X2
O
Crystal 2: Connection for other side of the crystal. When a crystal is used, a capacitor must be connected from this pin
to ground (see Figure 11). If X1/CLK is driven from an external source, this pin must be left open.
RxD
I
Receiver Serial Data Input: The least significant bit is received first. “Mark” is High; “space” is Low.
TxD
O
Transmitter Serial Data Output: The least significant bit is transmitted first. This output is held in the “mark” condition
when the transmitter is disabled, idle or operating in local loop back mode. “Mark” is High; “space” is Low.
OP0
O
Output 0: General-purpose output or request to send (RTSN, active-Low). Can be deactivated automatically on re-
ceive or transmit.
OP1
O
Output 1: General-purpose output.
OP2
O
Output 2: General-purpose output, or transmitter 1X or 16X clock output, or receiver 1X clock output.
OP3
O
Output 3: General-purpose output.
OP4
O
Output 4: General-purpose output or open-drain, active-Low, Rx interrupt ISR[1] output. DMA Control
OP5
O
Output 5: General-purpose output
OP6
O
Output 6: General-purpose output or open-drain, active-Low, Tx interrupt ISR[0] output. DMA Control
OP7
O
Output 7: General-purpose output.
IP0
I
Input 0: General-purpose input or clear to send active-Low input (CTSN). Has Change of State Dector.
IP1
I
Input 1: General-purpose input. Has Change of State Dector.
IP2
I
Input 2: General-purpose input or counter/timer external clock input. Has Change of State Dector.
IP3
I
Input 3: General-purpose input or transmitter external clock input (TxC). When the external clock is used by the trans-
mitter, the transmitted data is clocked on the falling edge of the clock. Has Change of State Dector.
IP4
I
Input 4: General-purpose input or receiver external clock input (RxC). When the external clock is used by the receiver,
the received data is sampled on the rising edge of the clock.
IP5
I
Input 5: General-purpose input
IP6
I
Input 6: General-purpose input
VCC
Pwr
Power Supply: +3.3 V or +5 V supply input
± 10 %
GND
Pwr
Ground
相關PDF資料 |
PDF描述 |
|---|---|
| SC28L91A1B,528 | IC UART SINGLE W/FIFO 44PQFP |
| SC28L91A1A,529 | IC UART SINGLE W/FIFO 44-PLCC |
| SCC68692C1A44,512 | IC UART DUAL 44-PLCC |
| SCC68692C1A44,518 | IC DUART 44PLCC |
| ATMEGA164PA-AUR | MCU AVR 16KB FLASH 20MHZ 44TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC28L91A1B-S | 功能描述:UART 接口集成電路 UART SINGLE W/FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC28L91A1B-T | 功能描述:UART 接口集成電路 3V-5V 1CH UART INTEL/MOT INTRF RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC28L92 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:3.3V-5.0V Dual Universal Asynchronous Receiver/Transmitter DUART |
| SC28L92A1A | 制造商:NXP Semiconductors 功能描述:UART DUAL 3.3V OR 5V SMD 28L92 |
| SC28L92A1A,512 | 功能描述:UART 接口集成電路 3V-5V 2CH UART INTEL/MOT INTRF RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。