- 您現在的位置：買賣IC網 > PDF目錄372128 > SC80C51BCYN40 (NXP SEMICONDUCTORS) CAT6 SOL PC PVC YEL 2FT PVC SOLID PATCH CORD PDF資料下載
參數資料
| 型號： | SC80C51BCYN40 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | CAT6 SOL PC PVC YEL 2FT PVC SOLID PATCH CORD |
| 中文描述： | 8-BIT, OTPROM, 16.5 MHz, MICROCONTROLLER, PDIP40 |
| 文件頁數： | 7/30頁 |
| 文件大?。?/td> | 411K |
| 代理商： | SC80C51BCYN40 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
Philips Semiconductors
Product specification
80C31/80C51/87C51
CMOS single-chip 8-bit microcontrollers
1996 Aug 16
7
PIN DESCRIPTION
PIN NO.
MNEMONIC
DIP
LCC
QFP
TYPE
NAME AND FUNCTION
V
SS
V
CC
20
22
16
I
Ground:
0V reference.
40
44
38
I
Power Supply:
This is the power supply voltage for normal, idle, and power-down
operation.
P0.0–0.7
39–32
43–36
37–30
I/O
Port 0:
Port 0 is an open-drain, bidirectional I/O port. Port 0 pins that have 1s written to
them float and can be used as high-impedance inputs. Port 0 is also the multiplexed
low-order address and data bus during accesses to external program and data memory. In
this application, it uses strong internal pull-ups when emitting 1s. Port 0 also outputs the
code bytes during program verification in the 87C51. External pull-ups are required during
program verification.
P1.0–P1.7
1–8
2–9
40-44,
1–3
I/O
Port 1:
Port 1 is an 8-bit bidirectional I/O port with internal pull-ups. Port 1 pins that have 1s
written to them are pulled high by the internal pull-ups and can be used as inputs. As
inputs, port 1 pins that are externally pulled low will source current because of the internal
pull-ups. (See DC Electrical Characteristics: I
IL
). Port 1 also receives the low-order address
byte during program memory verification.
P2.0–P2.7
21–28
24–31
18–25
I/O
Port 2:
Port 2 is an 8-bit bidirectional I/O port with internal pull-ups. Port 2 pins that have 1s
written to them are pulled high by the internal pull-ups and can be used as inputs. As
inputs, port 2 pins that are externally being pulled low will source current because of the
internal pull-ups. (See DC Electrical Characteristics: I
IL
). Port 2 emits the high-order
address byte during fetches from external program memory and during accesses to
external data memory that use 16-bit addresses (MOVX @DPTR). In this application, it
uses strong internal pull-ups when emitting 1s. During accesses to external data memory
that use 8-bit addresses (MOV @Ri), port 2 emits the contents of the P2 special function
register.
P3.0–P3.7
10–17
11,
13–19
5,
7–13
I/O
Port 3:
Port 3 is an 8-bit bidirectional I/O port with internal pull-ups. Port 3 pins that have 1s
written to them are pulled high by the internal pull-ups and can be used as inputs. As
inputs, port 3 pins that are externally being pulled low will source current because of the
pull-ups. (See DC Electrical Characteristics: I
IL
). Port 3 also serves the special features of
the 80C51 family, as listed below:
RxD (P3.0):
Serial input port
TxD (P3.1):
Serial output port
INT0 (P3.2):
External interrupt
INT1 (P3.3):
External interrupt
T0 (P3.4):
Timer 0 external input
T1 (P3.5):
Timer 1 external input
WR (P3.6):
External data memory write strobe
RD (P3.7):
External data memory read strobe
10
11
12
13
14
15
16
17
11
13
14
15
16
17
18
19
5
7
8
9
10
11
12
13
I
O
I
I
I
I
O
O
RST
9
10
4
I
Reset:
A high on this pin for two machine cycles while the oscillator is running, resets the
device. An internal diffused resistor to V
SS
permits a power-on reset using only an external
capacitor to V
CC
.
Address Latch Enable/Program Pulse:
Output pulse for latching the low byte of the
address during an access to external memory. In normal operation, ALE is emitted at a
constant rate of 1/6 the oscillator frequency, and can be used for external timing or clocking.
Note that one ALE pulse is skipped during each access to external data memory. This pin is
also the program pulse input (PROG) during EPROM programming.
ALE/PROG
30
33
27
I/O
PSEN
29
32
26
O
Program Store Enable:
The read strobe to external program memory. When the device is
executing code from the external program memory, PSEN is activated twice each machine
cycle, except that two PSEN activations are skipped during each access to external data
memory. PSEN is not activated during fetches from internal program memory.
EA/V
PP
31
35
29
I
External Access Enable/Programming Supply Voltage:
EA must be externally held low
to enable the device to fetch code from external program memory locations 0000H to
0FFFH. If EA is held high, the device executes from internal program memory unless the
program counter contains an address greater than 0FFFH. This pin also receives the
12.75V programming supply voltage (V
PP
) during EPROM programming.
Crystal 1:
Input to the inverting oscillator amplifier and input to the internal clock generator
circuits.
XTAL1
19
21
15
I
XTAL2
18
20
14
O
Crystal 2:
Output from the inverting oscillator amplifier.
相關PDF資料 |
PDF描述 |
|---|---|
| SC87C51CYK44 | CMOS single-chip 8-bit microcontrollers |
| SC87C51CGA44 | CMOS single-chip 8-bit microcontrollers |
| SC87C51CYA44 | CMOS single-chip 8-bit microcontrollers |
| SC87C51CYF40 | CMOS single-chip 8-bit microcontrollers |
| SC80C31BACA44 | Pressure Transducer, Series 19 mm, Compensated, Pressure Range: 0 psi to 15 psi, Absolute, 1/8-27 NPT, 10 Vdc excitation |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC80-M30/5 | 制造商:GardTec Inc 功能描述:SC Series 80 mm Steel Bright Nickel Chrome 4 Place Screw Mount Fan Guard |
| SC80-P10 | 制造商:GardTec Inc 功能描述:SC Series 80 mm Steel Bright Nickel Chrome 4 Place Screw Mount Fan Guard |
| SC80-P15/30 | 制造商:GardTec Inc 功能描述:SC Series Gardtec Fan guard |
| SC80-P15/45 | 制造商:GardTec Inc 功能描述:SC Series 80 mm Plastic Polyurethane Foam 4 Place Screw Mount Fan Guard |
| SC80-P40 | 制造商:GardTec Inc 功能描述:Plastic Fan Guard |
發布緊急采購，3分鐘左右您將得到回復。