- 您現在的位置：買賣IC網 > PDF目錄3763 > SCC2681AC1N40,112 (NXP Semiconductors)IC UART DUAL 40-DIP PDF資料下載
參數資料
| 型號： | SCC2681AC1N40,112 |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 2/29頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART DUAL 40-DIP |
| 產品培訓模塊： | Stand-Alone UARTs |
| 標準包裝： | 9 |
| 特點： | 故障啟動位檢測 |
| 通道數： | 2，DUART |
| FIFO's： | 3 位 |
| 電源電壓： | 5V |
| 帶并行端口： | 是 |
| 帶自動流量控制功能： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 40-DIP（0.600"，15.24mm） |
| 供應商設備封裝： | 40-DIP |
| 包裝： | 管件 |
| 其它名稱： | 568-3525-5 935274523112 SCC2681AC1N40 |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
Philips Semiconductors
Product data
SCC2681
Dual asynchronous receiver/transmitter (DUART)
2004 Apr 06
10
shift register is lost and the overrun error status bit (SR[4] will be
set-upon receipt of the start bit of the new (overrunning) character).
The receiver can control the deactivation of RTS. If programmed to
operate in this mode, the RTSN output will be negated (set to ‘1’)
when a valid start bit was received and the FIFO is full. When a
FIFO position becomes available, the RTSN output will be
re-asserted (set to ‘0’) automatically. This feature can be used to
prevent an overrun, in the receiver, by connecting the RTSN output
to the CTSN input of the transmitting device.
Receiver Reset and Disable
Receiver disable stops the receiver immediately – data being
assembled if the receiver shift register is lost. Data and status in the
FIFO is preserved and may be read. A re-enable of the receiver
after a disable will cause the receiver to begin assembling
characters at the next start bit detected.
A receiver reset will discard the present shift register data, reset the
receiver ready bit (RxRDY), clear the status of the byte at the top of
the FIFO and re-align the FIFO read/write pointers. This has the
appearance of “clearing or flushing” the receiver FIFO. In fact, the
FIFO is NEVER cleared! The data in the FIFO remains valid until
overwritten by another received character. Because of this,
erroneous reading or extra reads of the receiver FIFO will miss-align
the FIFO pointers and result in the reading of previously read data.
A receiver reset will re-align the pointers.
Multidrop Mode
Note: Please see
Application Note AN10251 for more information
on this feature.
The DUART is equipped with a wake up mode for multidrop
applications. This mode is selected by programming bits MR1A[4:3]
or MR1B[4:3] to ‘11’ for Channels A and B, respectively. In this mode
of operation, a ‘master’ station transmits an address character
followed by data characters for the addressed ‘slave’ station. The
slave stations, with receivers that are normally disabled, examine
the received data stream and ‘wake up’ the CPU (by setting RxRDY)
only upon receipt of an address character. The CPU compares the
received address to its station address and enables the receiver if it
wishes to receive the subsequent data characters. Upon receipt of
another address character, the CPU may disable the receiver to
initiate the process again.
A transmitted character consists of a start bit, the programmed
number of data bits, and Address/Data (A/D) bit, and the
programmed number of stop bits. The polarity of the transmitted A/D
bit is selected by the CPU by programming bit MR1A[2]/MR1B[2].
MR1A[2]/MR1B[2] = 0 transmits a zero in the A/D bit position, which
identifies the corresponding data bits as data while
MR1A[2]/MR1B[2] = 1 transmits a one in the A/D bit position, which
identifies the corresponding data bits as an address. The CPU
should program the mode register prior to loading the corresponding
data bits into the THR.
In this mode, the receiver continuously looks at the received data
stream, whether it is enabled or disabled. If disabled, it sets the
RxRDY status bit and loads the character into the RHR FIFO if the
received A/D bit is a one (address tag), but discards the received
character if the received A/D bit is a zero (data tag). If enabled, all
received characters are transferred to the CPU via the RHR. In
either case, the data bits are loaded into the data FIFO while the
A/D bit is loaded into the status FIFO position normally used for
parity error (SRA[5] or SRB[5]). Framing error, overrun error, and
break detect operate normally whether or not the receive is enabled.
相關PDF資料 |
PDF描述 |
|---|---|
| SC16IS760IBS,151 | IC UART I2C/SPI 24-HVQFN |
| XR16C854CJ-F | IC UART FIFO 128B QUAD 68PLCC |
| XR82C684CJ/44-F | IC UART CMOS QUAD 44PLCC |
| XR16C2850IJ-F | IC UART FIFO 128B 44PLCC |
| ST16C554DIJ68-F | IC UART FIFO 16B QUAD 68PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SCC2681AE1A44 | 功能描述:UART 接口集成電路 RPLACMNT FOR SCN2681 RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SCC2681AE1A44,512 | 功能描述:UART 接口集成電路 RPLACMNT FOR SCN2681 RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SCC2681AE1A44,518 | 功能描述:UART 接口集成電路 RPLACMNT FOR SCN2681 RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SCC2681AE1A44,529 | 功能描述:UART 接口集成電路 RPLACMNT FOR SCN2681 RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SCC2681AE1A44512 | 制造商:Rochester Electronics LLC 功能描述: 制造商:NXP Semiconductors 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。