- 您現在的位置：買賣IC網 > PDF目錄11823 > SCC2692AC1A44,518 (NXP Semiconductors)IC DUART SOT187-2 PDF資料下載
參數資料
| 型號： | SCC2692AC1A44,518 |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 26/30頁 |
| 文件大小： | 0K |
| 描述： | IC DUART SOT187-2 |
| 標準包裝： | 500 |
| 特點： | 故障啟動位檢測 |
| 通道數： | 2，DUART |
| FIFO's： | 3 位 |
| 電源電壓： | 5V |
| 帶并行端口： | 是 |
| 帶自動流量控制功能： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 44-LCC（J 形引線） |
| 供應商設備封裝： | 44-PLCC |
| 包裝： | 帶卷 (TR) |
| 其它名稱： | 933968320518 SCC2692AC1A44-T SCC2692AC1A44-T-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁
Philips Semiconductors
Product specification
SCC2692
Dual asynchronous receiver/transmitter (DUART)
1998 Sep 04
5
PIN DESCRIPTION
SYMBOL
APPLICABLE
TYPE
NAME AND FUNCTION
SYMBOL
40,44
28
TYPE
NAME AND FUNCTION
D0-D7
X
I/O
Data Bus: Bidirectional 3-State data bus used to transfer commands, data and status between the
DUART and the CPU. D0 is the least significant bit.
CEN
X
I
Chip Enable: Active-Low input signal. When Low, data transfers between the CPU and the DUART
are enabled on D0-D7 as controlled by the WRN, RDN and A0-A3 inputs. When High, places the
D0-D7 lines in the 3-State condition.
WRN
X
I
Write Strobe: When Low and CEN is also Low, the contents of the data bus are loaded into the
addressed register. The transfer occurs on the rising edge of the signal.
RDN
X
I
Read Strobe: When Low and CEN is also Low, causes the contents of the addressed register to be
presented on the data bus. The read cycle begins on the falling edge of RDN.
A0-A3
X
I
Address Inputs: Select the DUART internal registers and ports for read/write operations.
RESET
X
I
Reset: A High level clears internal registers (SRA, SRB, IMR, ISR, OPR, OPCR), puts OP0-OP7 in
the High state, stops the counter/timer, and puts Channels A and B in the inactive state, with the TxDA
and TxDB outputs in the mark (High) state. Resets Test modes, MR pointer set to MR1.
INTRN
X
O
Interrupt Request: Active-Low, open-drain, output which signals the CPU that one or more of the
eight maskable interrupting conditions are true.
X1/CLK
X
I
Crystal 1: Crystal connection or an external clock input. A crystal of a clock the appropriate frequency
(nominally 3.6864 MHz) must be supplied at all times. For crystal connections see Figure 7, Clock Timing.
X2
X
I
Crystal 2: Crystal connection. See Figure 7. If a crystal is not used it is best to keep this pin not
connected although it is permissible to ground it.
RxDA
X
I
Channel A Receiver Serial Data Input: The least significant bit is received first. “Mark” is High,
“space” is Low.
RxDB
X
I
Channel B Receiver Serial Data Input: The least significant bit is received first. “Mark” is High,
“space” is Low.
TxDA
X
O
Channel A Transmitter Serial Data Output: The least significant bit is transmitted first. This output is
held in the “mark” condition when the transmitter is disabled, idle or when operating in local loopback
mode. “Mark” is High, “space” is Low.
TxDB
X
O
Channel B Transmitter Serial Data Output: The least significant bit is transmitted first. This output
is held in the ‘mark’ condition when the transmitter is disabled, idle, or when operating in local
loopback mode. ‘Mark’ is High, ‘space’ is Low.
OP0
X
O
Output 0: General purpose output or Channel A request to send (RTSAN, active-Low). Can be
deactivated automatically on receive or transmit.
OP1
X
O
Output 1: General purpose output or Channel B request to send (RTSBN, active-Low). Can be
deactivated automatically on receive or transmit.
OP2
X
O
Output 2: General purpose output, or Channel A transmitter 1X or 16X clock output, or Channel A
receiver 1X clock output.
OP3
X
O
Output 3: General purpose output or open-drain, active-Low counter/timer output or Channel B
transmitter 1X clock output, or Channel B receiver 1X clock output.
OP4
X
O
Output 4: General purpose output or Channel A open-drain, active-Low, RxRDYAN/FFULLAN output.
OP5
X
O
Output 5: General purpose output or Channel B open-drain, active-Low, RxRDYBN/FFULLBN output.
OP6
X
O
Output 6: General purpose output or Channel A open-drain, active-Low, TxRDYAN output.
OP7
X
O
Output 7: General purpose output, or Channel B open-drain, active-Low, TxRDYBN output.
IP0
X
I
Input 0: General purpose input or Channel A clear to send active-Low input (CTSAN). Pin has an
internal VCC pull-up device supplying 1 to 4 mA of current.
IP1
X
I
Input 1: General purpose input or Channel B clear to send active-Low input (CTSBN). Pin has an
internal VCC pull-up device supplying 1 to 4 mA of current.
IP2
X
I
Input 2: General purpose input or counter/timer external clock input. Pin has an internal VCC pull-up
device supplying 1 to 4
mA of current.
IP3
X
I
Input 3: General purpose input or Channel A transmitter external clock input (TxCA). When the
external clock is used by the transmitter, the transmitted data is clocked on the falling edge of the
clock. Pin has an internal VCC pull-up device supplying 1 to 4 mA of current.
IP4
X
I
Input 4: General purpose input or Channel A receiver external clock input (RxCA). When the external
clock is used by the receiver, the received data is sampled on the rising edge of the clock. Pin has an
internal VCC pull-up device supplying 1 to 4 mA of current.
IP5
X
I
Input 5: General purpose input or Channel B transmitter external clock input (TxCB). When the
external clock is used by the transmitter, the transmitted data is clocked on the falling edge of the
clock. Pin has an internal VCC pull-up device supplying 1 to 4 mA of current.
IP6
X
I
Input 6: General purpose input or Channel B receiver external clock input (RxCB). When the external
clock is used by the receiver, the received data is sampled on the rising edge of the clock. Pin has an
internal VCC pull-up device supplying 1 to 4 mA of current.
VCC
X
I
Power Supply: +5V supply input.
GND
X
I
Ground
相關PDF資料 |
PDF描述 |
|---|---|
| VI-B32-IY | CONVERTER MOD DC/DC 15V 50W |
| FT2232HQ-TRAY | IC USB HS DUAL UART/FIFO 64-QFN |
| SCC68681C1A44,529 | IC UART DUAL 44-PLCC |
| VI-B2Z-IY | CONVERTER MOD DC/DC 2V 20W |
| VE-J5J-IW-F4 | CONVERTER MOD DC/DC 36V 100W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SCC2692AC1A44-S | 功能描述:UART 接口集成電路 5V INDSTRL UART 2 C RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SCC2692AC1B44 | 功能描述:UART 接口集成電路 5V INDSTRL UART 2 C RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SCC2692AC1B44,528 | 功能描述:UART 接口集成電路 5V INDSTRL UART 2 C RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SCC2692AC1B44,551 | 功能描述:UART 接口集成電路 5V INDSTRL UART 2 C RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SCC2692AC1B44,557 | 功能描述:UART 接口集成電路 5V INDSTRL UART 2 C RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。