- 您現在的位置：買賣IC網 > PDF目錄372129 > SCC68692 (NXP Semiconductors N.V.) Dual asynchronous receiver/transmitter DUART PDF資料下載
參數資料
| 型號： | SCC68692 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Dual asynchronous receiver/transmitter DUART |
| 中文描述： | 雙異步接收器/發送器杜阿爾特 |
| 文件頁數： | 25/30頁 |
| 文件大小： | 193K |
| 代理商： | SCC68692 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁
Philips Semiconductors
Product specification
SCC68692
Dual asynchronous receiver/transmitter (DUART)
1998 Sep 04
25
TRANSMITTER
ENABLED
TxD
ADD#1
TxRDY
(SR2)
CSN
(WRITE)
MR1(4+3) = 11
MR1(2) = 1
1
BIT 9
D0
0
BIT 9
ADD#2 1
BIT 9
MASTER STATION
ADD#1MR1(2) = 0 D0
MR1(2) = 1 ADD#2
RxD
ADD#1 1
BIT 9
D0
0
BIT 9
ADD#2 1
BIT 9
PERIPHERAL STATION
0
BIT 9
0
BIT 9
RECEIVER
ENABLED
RxRDY
(SR0)
CSN
MR1(4:3) = 11
ADD#1
STATUS DATA
D0
STATUS DATA
ADD#2
SD00120
Figure 14. Wake-Up Mode
INTRN
D0–D7
TxDA/B
OP0–OP7
150pF
2.15V
750
50pF
+5V
2.7K
SD00151
Figure 15. Test Conditions on Outputs
Output Port Notes
The output ports are controlled from four places: the OPCR register,
the OPR register, the MR registers and the command register. The
OPCR register controls the source of the data for the output ports
OP2 through OP7. The data source for output ports OP0 and OP1
is controlled by the MR and CR registers. When the OPR is the
source of the data for the output ports, the data at the ports is
inverted from that in the OPR register. The content of the OPR
register is controlled by the “Set Output Port Bits Command” and the
“Reset Output Bits Command”. These commands are at E and F,
respectively. When these commands are used, action takes place
only at the bit locations where ones exist. For example, a one in bit
location 5 of the data word used with the “Set Output Port Bits”
command will result in OPR5 being set to one. The OP5 would then
be set to zero (V
SS
). Similarly, a one in bit position 5 of the data
word associated with the “Reset Output Ports Bits” command would
set OPR5 to zero and, hence, the pin OP5 to a one (V
DD
).
The CTS, RTS, CTS Enable Tx signals
CTS (Clear To Send) is usually meant to be a signal to the
transmitter meaning that it may transmit data to the receiver. The
CTS input is on pin MPI. The CTS signal is active low; thus, it is
called CTS.
RTS is usually meant to be a signal from the receiver indicating that
the receiver is ready to receive data. It is also active low and is,
thus, called RTSN. RTSN is on pin MP0. A receiver’s RTS output
will usually be connected to the CTS input of the associated
transmitter. Therefore, one could say that RTS and CTS are
different ends of the same wire!
MR2(4) is the bit that allows the transmitter to be controlled by the
CTS pin (MPI). When this bit is set to one AND the CTS input is
driven high, the transmitter will stop sending data at the end of the
present character being serialized. It is usually the RTS output of
the receiver that will be connected to the transmitter’s CTS input.
The receiver will set RTS high when the receiver FIFO is full AND
the start bit of the fourth character is sensed. Transmission then
stops with four valid characters in the receiver. When MR2(4) is set
to one, CTSN must be at zero for the transmitter to operate. If
MR2(4) is set to zero, the MP pin will have no effect on the operation
of the transmitter.
MR1(7) is the bit that allows the receiver to control MP0. When MP0
is controlled by the receiver, the meaning of that pin will be RTS.
However, a point of confusion arises in that MP0 may also be
controlled by the transmitter. When the transmitter is controlling this
pin, its meaning is not RTS at all. It is, rather, that the transmitter
has finished sending its last data byte. Programming the MP0 pin to
相關PDF資料 |
PDF描述 |
|---|---|
| SCC68692C1F40 | Dual asynchronous receiver/transmitter DUART |
| SCC68692E1F40 | Dual asynchronous receiver/transmitter DUART |
| SCG002 | InGaP HBT Gain Block |
| SCG002_07 | InGaP HBT Gain Block |
| SCG002B-G | InGaP HBT Gain Block |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SCC68692C1A44 | 功能描述:UART 接口集成電路 2CH. 5V IND. UART MOT INTERF. RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SCC68692C1A44,512 | 功能描述:UART 接口集成電路 2CH. 5V IND. UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SCC68692C1A44,518 | 功能描述:UART 接口集成電路 5V IND. UART 2 CH. MOT INTERF. RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SCC68692C1A44,529 | 功能描述:UART 接口集成電路 5V IND. UART 2 CH. RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SCC68692C1A44512 | 制造商:NXP Semiconductors 功能描述:IC DUAL UART FIFO 1MBPS 5.5V LCC-44 |
發布緊急采購，3分鐘左右您將得到回復。