- 您現在的位置：買賣IC網 > PDF目錄372130 > SCN68681C1A44 (NXP SEMICONDUCTORS) RES 16K OHM 1/16W 0.1% 0402 SMD PDF資料下載
參數資料
| 型號： | SCN68681C1A44 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | RES 16K OHM 1/16W 0.1% 0402 SMD |
| 中文描述： | 2 CHANNEL(S), 1M bps, SERIAL COMM CONTROLLER, PQCC44 |
| 封裝： | PLASTIC, MS-018, LCC-44 |
| 文件頁數： | 16/28頁 |
| 文件大?。?/td> | 187K |
| 代理商： | SCN68681C1A44 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
Philips Semiconductors
Product specification
SCN68681
Dual asynchronous receiver/transmitter (DUART)
1998 Sep 04
16
1: The Channel A receiver interrupt output which is the complement
of ISR[1]. When in this mode OP4 acts as an open-drain output.
Note that this output is not masked by the contents of the IMR.
OPCR[3:2] – OP3 Output Select
This bit programs the OP3 output to provide one of the following:
00: The complement of OPR[3].
01: The counter/timer output, in which case OP3 acts as an open-
drain output. In the timer mode, this output is a square wave at
the programmed frequency. In the counter mode, the output
remains High until terminal count is reached, at which time it
goes Low. The output returns to the High state when the count-
er is stopped by a stop counter command. Note that this output
is not masked by the contents of the IMR.
10: The 1X clock for the Channel B transmitter, which is the clock
that shifts the transmitted data. If data is not being transmitted,
a free running 1X clock is output.
11: The 1X clock for the Channel B receiver, which is the clock that
samples the received data. If data is not being received, a free
running 1X clock is output.
OPCR[1:0] – OP2 Output Select
This field programs the OP2 output to provide one of the following:
00: The complement of OPR[2].
01: The 16X clock for the Channel A transmitter. This is the clock
selected by CSRA[3:0], and will be a 1X clock if CSRA[3:0] = 1111.
10: The 1X clock for the Channel A transmitter, which is the clock
that shifts the transmitted data. If data is not being transmitted,
a free running 1X clock is output.
11: The 1X clock for the Channel A receiver, which is the clock that
samples the received data. If data is not being received, a free
running 1X clock is output.
Table 4.
Bit Rate Generator Characteristics
Crystal or Clock = 3.6864MHz
NORMAL RATE
(BAUD)
CLOCK (kHz)
ACTUAL 16x
ERROR (%)
50
75
110
0.8
1.2
0
0
1.759
2.153
2.4
3.2
4.8
9.6
16.756
19.2
28.8
32.056
38.4
76.8
115.2
153.6
230.4
307.2
460.8
614.4
921.6
1843.2K
-0.069
0.059
134.5
150
200
300
600
1050
1200
1800
2000
2400
4800
7200
9600
14.4K
19.2k
28.8K
38.4k
57.6K
115.2K
0
0
0
0
-0.260
0
0
0.175
0
0
0
0
0
0
0
0
0
0
NOTE:
Duty cycle of 16x clock is 50%
±
1%.
Asynchronous UART communications can tolerate frequency error
of 4.1% to 6.7% in a “clean” communications channel. The percent
of error changes as the character length changes. The above
percentages range from 5 bits not parity to 8 bits with parity and one
stop bit. The error with 8 bits no parity and one stop bit is 4.6%. If a
stop bit length of 9/16 is used, the error tolerance will approach 0
due to a variable error of up to 1/16 bit time in receiver clock phase
alignment to the start bit.
Table 5.
ACR
[6:4]
000
001
ACR 6:4 Field Definition
MODE
CLOCK SOURCE
Counter
Counter
External (IP2)*
TxCA – 1x clock of Channel
A transmitter
TxCB – 1x clock of Channel
B transmitter
Crystal or external clock
(x1/CLK) divided by 16
External (IP2)*
External (IP2) divided by 16*
Crystal or external clock
(X1/CLK)
Crystal or external clock
(X1/CLK) divided by 16
010
Counter
011
Counter
100
101
110
Timer (square wave)
Timer (square wave)
Timer (square wave)
111
NOTE:
*
In these modes, the Channel B receiver clock should normally be
generated from the baud rate generator. Timer mode generates
squarewave.
Timer (square wave)
ACR – Auxiliary Control Register
ACR[7] – Baud Rate Generator Set Select
This bit selects one of two sets of baud rates to be generated by the
BRG:
Set 1: 50, 110, 134.5, 200, 300, 600, 1.05k, 1.2k, 2.4k, 4.8k, 7.2k,
9.6k, and 38.4k baud.
Set 2: 75, 110, 134.5, 150, 300, 600, 1.2k, 1.8k, 2.0k, 2.4k, 4.8k,
9.6k, and 19.2k baud.
The selected set of rates is available for use by the Channel A and
B receivers and transmitters as described in CSRA and CSRB.
Baud rate generator characteristics are given in Table 4.
ACR[6:4] – Counter/Timer Mode And Clock Source Select
This field selects the operating mode of the counter/timer and its
clock source as shown in Table 5.
ACR[3:0] – IP3, IP2, IP1, IP0 Change-of-State Interrupt Enable
This field selects which bits of the input port change register (IPCR)
cause the input change bit in the interrupt status register (ISR[7]) to
be set. If a bit is in the ‘on’ state the setting of the corresponding bit
in the IPCR will also result in the setting of ISR[7], which results in
the generation of an interrupt output if IMR[7] = 1. If a bit is in the
‘off’ state, the setting of that bit in the IPCR has no effect on ISR[7].
IPCR – Input Port Change Register
IPCR[7] – IP3, IP2, IP1, IP0 Change-of-State
These bits are set when a change-of-state, as defined in the input
port section of this data sheet, occurs at the respective input pins.
They are cleared when the IPCR is read by the CPU. A read of the
IPCR also clears ISR[7], the input change bit in the interrupt status
register. The setting of these bits can be programmed to generate
an interrupt to the CPU.
相關PDF資料 |
PDF描述 |
|---|---|
| SCN8039H | SINGLE-CHIP 8-BIT MICROCONTROLLER |
| SCN8049H | SINGLE-CHIP 8-BIT MICROCONTROLLER |
| SCN8050H | SINGLE-CHIP 8-BIT MICROCONTROLLER |
| SCN8051HCCA44 | SINGLE CHIP 8 BIT MICROCONTROLLER |
| SCN8031HCCN40 | SINGLE CHIP 8 BIT MICROCONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SCN68681C1N40 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Dual asynchronous receiver/transmitter DUART |
| SCN68681E1A44 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Dual asynchronous receiver/transmitter DUART |
| SCN68681E1F40 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Dual asynchronous receiver/transmitter DUART |
| SCN68681E1N40 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Dual asynchronous receiver/transmitter DUART |
| SCN-800 | 制造商:MEANWELL 制造商全稱:Mean Well Enterprises Co., Ltd. 功能描述:800W Single Output With Parallel Function |
發布緊急采購，3分鐘左右您將得到回復。