
- 7 / 21 -
(SCP69G4 / 6EG4-GL)
Specification : TS-S03D114E
March, 2005
5. Absolute Maximum Ratings
Warning
Use the product with the rated voltage described in the specification. If the voltage exceeds the maximum rating, overheating or
fire may occur.
6. Electrical Interface
( Unless otherwise specified, VccT,R = 3.135 to 3.465 V and all operating temperature shall apply. )
6-1. Operating Characteristics
6-2. Transmitter side
Symbol
Min.
Typ.
Max.
Unit
Note
Supply Voltage
VccT,R
3.135
3.30
3.465
V
Pow er Dissipation
Pw
1000
mW
1
Note
1. 1250Mbps, PRBS2^7-1, NRZ, 50% duty cycle data.
Parameter
Symbol
Min.
Typ.
Max.
Unit
Note
Dif ferential Input Voltage Sw ing (TD+,TD-)
Vin
0.5
2.4
Vp-p
1
Input Dif ferential Impedance
Zin
80
100
120
Tx Fault
Fault
Vf aultH
2.0
VccT+0.3
V
2, 3
Normal
Vf aultL
0
0.8
V
2, 3, 4
Tx Disable
Disable
Vdi
2.0
VccT+0.3
V
Enable
Vei
0
0.8
V
Tdis Input Current
High
lds
-1
50
A
Notes
1. Refer to Figure 7.
2. Tx Fault is pulled up to VccT w ith a 4.7k-10k resistor on the host board.
When high, output indicates a laser f ault of some kind. Low indicates normal operation.
3. Refer to section 7-4 about Tx Fault and Tx Shutdow n behavior.
4. Sink Current : 1mA
5. Tx Disable input is internally terminated to VccT via 4.7 k resistor. If pin3 is left open, Tx is disable.
Parameter
5
Parameter
Symbol
Min.
Typ.
Max.
Unit
Note
Storage Ambient Temperature
Ts
-40
-
85
°C
1
Operating Case Temperature
Tc
-5
-
70
°C
Optical Input Level
Pin
3.0
dBm
Supply Voltage
VccT,R
-0.3
-
4.0
V
Input Voltage
Vi
0
-
VccT,R+0.3
V
2
Dif ferential Input Voltage Sw ing (TD+,TD-)
Vin
2.5
Vp-p
Notes
1. No condensation allowed. 2: For MODE-DEF (1:2)
Caution
Do not store the product in the area where temperature exceeds the maximum rating, where there is too much moisture or
dampness, where there is acid gas or corrosive gas, or other extreme conditions. Otherwise, failure, overheating or fire may
occur.
6-3. Receiver side
Figure 7. Definition of Differential
Input / Output Voltage Swing
Bias Volt ag e
Input / Output V oltage Sw in g (V s w ing)
D if ferent ial Input / Out put Volt ag e Sw in g (V in / Vout) = 2 X Vs w ing
Parameter
Symbol
Min.
Typ.
Max.
Unit
Note
Dif ferential Output Voltage Sw ing (RD+,RD-)
Vout
0.5
1.2
Vp-p
1
LOS
High
Vloh
2.0
VccR+0.3
V
2
Output Voltage
Low
Vlol
0
0.8
V
2, 3
Data Rise / Fall Time
tr / tf
240
psec
4
Notes
1. Vcc=+3.3V +/-5%, Output load resistance Rdif =100. Refer to Figure1-(B).
Refer to Figure7. about definition of diff erential sw ing.
2. LOS is pulled up to VccR w ith a 4.7k - 10k resistor on the host board. Low indicates normal operation.
3. Sink Current : 1mA 4. 20 to 80%, 1250Mbps, PRBS 2^7-1, NRZ, 50% duty cycle data.