- 您現在的位置：買賣IC網 > PDF目錄372144 > SHC298JU Monolithic SAMPLE/HOLD AMPLIFIER PDF資料下載
參數資料
| 型號： | SHC298JU |
| 元件分類： | 運動控制電子 |
| 英文描述： | Monolithic SAMPLE/HOLD AMPLIFIER |
| 中文描述： | 單片采樣/保持放大器 |
| 文件頁數： | 7/8頁 |
| 文件大?。?/td> | 100K |
| 代理商： | SHC298JU |
7
SHC298/298A
CHARGE OFFSET
Charge Offset is the offset that results from the charge
coupled through the gate capacitance of the switching FET.
This charge is coupled into the storage capacitor when the
FET is switched to the “hold” mode.
OPERATING INSTRUCTIONS
EXTERNAL CAPACITOR SELECTION
Capacitors with high insulation resistance and low dielectric
absorption, such as Teflon
, polystyrene or polypropylene
units, should be used as storage elements (polystyrene should
not be used above +85
°
C). Care should be taken in the
printed circuit layout to minimize AC and DC leakage
currents from the capacitor to reduce charge offset and
droop errors.
The value of the external capacitor determines the droop,
charge offset and acquisition time of the Sample/Hold. Both
droop and charge offset will vary linearly with capacitance
from the values given in the specification table for a 0.001
μ
F
capacitor. With a capacitor of 0.01
μ
F, the droop will reduce
to approximately 2.5
μ
V/ms and the charge offset to approxi-
mately 1.5mV. The behavior of acquisition time with changes
in external capacitance is shown in the Typical Performance
Curves.
OFFSET ADJUSTMENT
The offset should be adjusted with the input grounded.
During the adjustment, the sample/hold should be switching
continuously between the Sample and the Hold mode. The
error should then be adjusted to zero when the unit is in the
Hold mode. In this way, charge offset as well as amplifier
offset will be adjusted. When a 0.001
μ
F capacitor is used, it
will not be possible to adjust the full offset error at the
sample/hold. It should be adjusted elsewhere in the system.
APPLICATIONS
DATA ACQUISITION
The SHC298 may be used to hold data for conversion with
an analog-to-digital converter or used to provide Pulse
Amplitude Modulation (PAM) data output (see Figures 2
and 3).
DATA DISTRIBUTION
The SHC298 may be used to hold the output of a digital-to-
analog converter whose digital inputs are multiplexed (see
Figure 4).
TEST SYSTEMS
The SHC298 is also well suited for use in test systems to
acquire and hold data transients for human operators or for
the other parts of the test system such as comparators, digital
voltmeters, etc.
With a 0.1
μ
F storage capacitor, the output may be held 10
seconds with less than 0.1% error. With a 1
μ
F storage
capacitor, the output may be held more than 15 minutes with
less than 1% error.
CAPACITIVE LOADING
SHC298 is sensitive to capacitive loading on the output and
may oscillate. When driving long lines, a buffer should be
used.
HIGH SPEED DATA ACQUISITION
The minimum sample time for one channel in a data acqui-
sition system is usually considered to be the acquisition time
of the sample/hold plus the conversion time of the analog-to-
digital converter. If two or more sample/holds are used with
a high-speed multiplexer, the acquisition time of the sample/
hold can be virtually eliminated. While the first channel is in
hold and switched on to the ADC, the multiplexer may be
addressed to the next channel. The second sample/hold will
have acquired this data by the time the conversion is com-
plete. Then, the sample/holds reverse roles and another
channel is addressed (see Figure 5). For low-level systems,
and instrumentation amplifier and double-ended multiplexer
may be connected to the sample/hold inputs. The settling
time of the multiplexer, instrumentation amplifier, and
sample/hold can be eliminated from the channel conversion
time as before.
FIGURE 2. Data Acquisition.
FIGURE 3. PAM Output.
Mode Control Hold
Actual Input
PAM Output
0.1μF
SHC298
0.005μF
Storage
4
6
–15VDC
0.1μF
24k
1k
+15VDC
To A/D
Converter
PAM
Output
Mode
Control
7
2
1
5
3
8
Analog
Multiplexer
Analog
Inputs
Teflon, DuPont de Nemours
相關PDF資料 |
PDF描述 |
|---|---|
| SHC5320KP | High-Speed, Bipolar, Monolithic SAMPLE/HOLD AMPLIFIER |
| SHC5320SH | High-Speed, Bipolar, Monolithic SAMPLE/HOLD AMPLIFIER |
| SHC5320KU | High-Speed, Bipolar, Monolithic SAMPLE/HOLD AMPLIFIER |
| SHC5320 | High-Speed, Bipolar, Monolithic SAMPLE/HOLD AMPLIFIER |
| SHC5320KH | High-Speed, Bipolar, Monolithic SAMPLE/HOLD AMPLIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SHC-2R5M | 制造商:PREMO 制造商全稱:PREMO CORPORATION S.L 功能描述:SMD Power Inductors Shielded |
| SHC3 | 制造商:CIT 制造商全稱:CIT Relay & Switch 功能描述:CIT SWITCH |
| SHC-30 | 功能描述:CLAMP SNAP-IT .469-.531" RoHS:是 類別:線纜，導線 - 管理 >> 線夾和夾具 系列:SHC 標準包裝:100 系列:TC 類型:C-夾 開口尺寸:0.79" L x 0.54" W x 0.67" H（20.1mm x 13.7mm x 17.0mm） 安裝類型:釘子 材質:聚丙烯 顏色:黑 |
| SHC-30-100PK | 制造商:Richco 功能描述:SNAP-IT HOSE CLAMPS 15/32-17/32 |
| SHC-32 | 功能描述:CLAMP SNAP-IT .531-.594" RoHS:是 類別:線纜，導線 - 管理 >> 線夾和夾具 系列:SHC 標準包裝:100 系列:TC 類型:C-夾 開口尺寸:0.79" L x 0.54" W x 0.67" H（20.1mm x 13.7mm x 17.0mm） 安裝類型:釘子 材質:聚丙烯 顏色:黑 |
發布緊急采購，3分鐘左右您將得到回復。