- 您現在的位置：買賣IC網 > PDF目錄373395 > SI3210 (Electronic Theatre Controls, Inc.) PROSLIC PROGRAMMABLE CMOS SLIC/CODEC WITH RINGING/BATTERY VOLTAGE GENERATION PDF資料下載
參數資料
| 型號： | SI3210 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 元件分類： | Codec |
| 英文描述： | PROSLIC PROGRAMMABLE CMOS SLIC/CODEC WITH RINGING/BATTERY VOLTAGE GENERATION |
| 中文描述： | ProSLIC產品可編程的CMOS用戶接口/有振鈴編解碼器/電池電壓生成 |
| 文件頁數： | 22/122頁 |
| 文件大小： | 1950K |
| 代理商： | SI3210 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁
Si3210/Si3211/Si3212
22
Preliminary Rev. 1.11
Linefeed Architecture
The ProSLIC is a low-voltage CMOS device that uses
low-cost external components to control the high
voltages required for subscriber line interfaces.
Figure 15 is a simplified illustration of the linefeed
control loop circuit for TIP or RING and the external
components used.
The ProSLIC uses both voltage and current sensing to
control TIP and RING. DC and AC line voltages on TIP
and RING are measured through sense resistors R
DC
and R
AC
, respectively. The ProSLIC uses linefeed
transistors Q
P
and Q
N
to drive TIP and RING. Q
DN
isolates the high-voltage base of Q
N
from the ProSLIC.
The ProSLIC measures voltage at various nodes in
order to monitor the linefeed current. R
DC
, R
SE
, and
R
BAT
provide access to these measuring points. The
sense circuitry is calibrated on-chip to guarantee
measurement
accuracy
component tolerances. See "Linefeed Calibration" on
page 26 for details.
with
standard
external
Linefeed Operation States
The ProSLIC linefeed has eight states of operation as
shown in Table 21. The state of operation is controlled
using the Linefeed Control register (direct Register 64).
The open state turns off all currents into the external
bipolar transistors and can be used in the presence of
fault conditions on the line and to generate Open Switch
Intervals (OSIs). TIP and RING are effectively tri-stated
with a dc output impedance of about 150 k
. The
ProSLIC can also automatically enter the open state if it
detects excessive power being consumed in the
external bipolar transistors. See "Power Monitoring and
Line Fault Detection" on page 24 for more details.
In the forward active and reverse active states, linefeed
circuitry is on and the audio signal paths are powered
down.
In the forward and reverse on-hook transmission states
audio signal paths are powered up to provide data
transmission during an on-hook loop condition.
The TIP Open state turns off all control currents to the
external bipolar devices connected to TIP and provides
an active linefeed on RING for ground start operation.
The RING Open state provides similar operation with
the RING drivers off and TIP active.
The ringing state drives programmable ringing
waveforms onto the line.
Loop Voltage and Current Monitoring
The ProSLIC continuously monitors the TIP and RING
voltages and external BJT currents. These values are
available in registers 78–89. Table 22 on page 24 lists
the values that are measured and their associated
registers. An internal A/D converter samples the
measured voltages and currents from the analog sense
circuitry and translates them into the digital domain. The
A/D updates the samples at an 800 Hz rate. Two
derived values are also reported—loop voltage and loop
current. The loop voltage, V
TIP
– V
RING
, is reported as a
1-bit sign, 6-bit magnitude format. For ground start
operation the reported value is the RING voltage. The
loop current, (I
Q1
– I
Q2
+ I
Q5
–I
Q6
)/2, is reported in a 1-
bit sign, 6-bit magnitude format. In RING open and TIP
open states the loop current is reported as (I
Q1
– I
Q2
) +
(I
Q5
–I
Q6
).
相關PDF資料 |
PDF描述 |
|---|---|
| SI3210-BT | PROSLIC PROGRAMMABLE CMOS SLIC/CODEC WITH RINGING/BATTERY VOLTAGE GENERATION |
| SI3210-KT | PROSLIC PROGRAMMABLE CMOS SLIC/CODEC WITH RINGING/BATTERY VOLTAGE GENERATION |
| SI3211-BT | PROSLIC PROGRAMMABLE CMOS SLIC/CODEC WITH RINGING/BATTERY VOLTAGE GENERATION |
| SI3211-KT | PROSLIC PROGRAMMABLE CMOS SLIC/CODEC WITH RINGING/BATTERY VOLTAGE GENERATION |
| SI3212 | PROSLIC PROGRAMMABLE CMOS SLIC/CODEC WITH RINGING/BATTERY VOLTAGE GENERATION |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SI3210-BT | 功能描述:電信線路管理 IC CONTACT SILICON LABS FOR AVAILABILITY RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| SI3210-BTR | 功能描述:電信線路管理 IC Sgl Ch SLIC/Codec w/ DTMF Decoder RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| SI3210DC1-EVB | 功能描述:子卡和OEM板 Si3210M Daughter Crd W/ SI3201 INTERFACE RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit |
| SI3210DCQ1-EVB | 功能描述:子卡和OEM板 Si3210 QFN Daughter Card RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit |
| SI3210DCQX-EVB | 功能描述:子卡和OEM板 Si3210 QFN Daughter Card RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit |
發布緊急采購，3分鐘左右您將得到回復。