- 您現在的位置：買賣IC網 > PDF目錄373395 > SI3211 (Electronic Theatre Controls, Inc.) PROSLIC PROGRAMMABLE CMOS SLIC/CODEC WITH RINGING/BATTERY VOLTAGE GENERATION PDF資料下載
參數資料
| 型號： | SI3211 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 元件分類： | Codec |
| 英文描述： | PROSLIC PROGRAMMABLE CMOS SLIC/CODEC WITH RINGING/BATTERY VOLTAGE GENERATION |
| 中文描述： | ProSLIC產品可編程的CMOS用戶接口/有振鈴編解碼器/電池電壓生成 |
| 文件頁數： | 30/122頁 |
| 文件大小： | 1950K |
| 代理商： | SI3211 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁
Si3210/Si3211/Si3212
30
Preliminary Rev. 1.11
DC-DC Converter Enhancements
Silicon
revisions
enhancements to the dc-dc converter. The first is a
multi-threshold error control algorithm that enables the
dc-dc converter to adjust more quickly to voltage
changes. This option is enabled by setting DCSU = 1
(direct Register 108, bit 5). The second enhancement is
an audio band filter that removes audio band noise from
the dc-dc converter control loop. This option is enabled
by setting DCFIL = 1 (direct Register 108, bit 1).
C
and
higher
support
two
DC-DC Converter During Ringing
When the ProSLIC enters the ringing state, it requires
voltages well above those used in the active mode. The
voltage to be generated and regulated by the dc-dc
converter during a ringing burst is set using the VBATH
register (direct Register 74). VBATH can be set between
0 and –94.5 V in 1.5 V steps. To avoid clipping the
ringing signal, V
BATH
must be set larger than the ringing
amplitude. At the end of each ringing burst the dc-dc
converter adjusts back to active state regulation as
described above.
External Battery Switching (Si3211 and Si3212 Only)
The Si3211 and Si3212 support switching between two
battery voltages. The circuit for external battery
switching is defined in Figure 12. Typically a high
voltage battery (e.g., –70 V) is used for on-hook and
ringing states, and a low voltage battery (e.g., –24 V) is
used for the off-hook condition. The ProSLIC uses an
external transistor to switch between the two supplies.
When the ProSLIC changes operating states, it
automatically switches battery supplies if the automatic/
manual control bit ABAT (direct Register 67, bit 3) is set.
For example, the ProSLIC will switch from high battery
to low battery when it detects an off-hook event through
either a ring trip or loop closure event. If automatic
battery selection is disabled (ABAT = 0), the battery is
selected by the Battery Feed Select bit, BATSL (direct
Register 66, bit 1).
Silicon revisions C and higher support the option to add
a 60 ms debounce period to the battery switching circuit
when transitioning from high battery to low battery. This
option is enabled by setting SWDB = 1 (direct
Register 108, bit 3). This debounce minimizes battery
transitions in the case of pulse dialing or other quick on-
hook to off-hook transitions.
Tone Generation
Two digital tone generators are provided in the ProSLIC.
They allow the generation of a wide variety of single or
dual tone frequency and amplitude combinations and
spare the user the effort of generating the required
POTS signaling tones on the PCM highway. DTMF, FSK
(caller ID), call progress, and other tones can all be
generated on-chip. The tones can be sent to either the
receive or transmit paths (see Figure 23 on page 40).
Tone Generator Architecture
A simplified diagram of the tone generator architecture
is shown in Figure 18. The oscillator, active/inactive
timers, interrupt block, and signal routing block are
connected to give the user flexibility in creating audio
signals. Control and status register bits are placed in the
figure to indicate their association with the tone
generator architecture. These registers are described in
more detail in Table 27.
相關PDF資料 |
PDF描述 |
|---|---|
| SI3210M-KT | PROSLIC PROGRAMMABLE CMOS SLIC/CODEC WITH RINGING/BATTERY VOLTAGE GENERATION |
| SI3210M-BT | PROSLIC PROGRAMMABLE CMOS SLIC/CODEC WITH RINGING/BATTERY VOLTAGE GENERATION |
| SI3210 | PROSLIC PROGRAMMABLE CMOS SLIC/CODEC WITH RINGING/BATTERY VOLTAGE GENERATION |
| SI3210-BT | PROSLIC PROGRAMMABLE CMOS SLIC/CODEC WITH RINGING/BATTERY VOLTAGE GENERATION |
| SI3210-KT | PROSLIC PROGRAMMABLE CMOS SLIC/CODEC WITH RINGING/BATTERY VOLTAGE GENERATION |
相關代理商/技術參數 |
參數描述 |
|---|---|
| Si3211-BT | 功能描述:電信線路管理 IC Single-Channel SLIC/ Codec RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| SI3211-BTR | 制造商:Silicon Laboratories Inc 功能描述: |
| Si3211-E-FT | 功能描述:電信線路管理 IC Single-Channel SLIC/Codec RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| SI3211-E-FTR | 功能描述:電信線路管理 IC Single-CH SLIC/Codec DTMF Decoder RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| Si3211-E-GM | 功能描述:電信線路管理 IC SNGL-Ch SLIC/Code WITH DTMF Decoder RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。