參數資料
型號: SI3216-C-FT
廠商: Silicon Laboratories Inc
文件頁數: 65/122頁
文件大?。?/td> 0K
描述: IC SLIC/CODEC 1CH 38TSSOP
標準包裝: 50
系列: ProSLIC®
功能: 用戶線路接口概念(SLIC),CODEC
接口: GCI,PCM,SPI
電路數: 1
電源電壓: 3.13 V ~ 5.25 V
電流 - 電源: 88mA
功率(瓦特): 700mW
工作溫度: 0°C ~ 70°C
安裝類型: 表面貼裝
封裝/外殼: 38-TFSOP(0.173",4.40mm 寬)
供應商設備封裝: 38-TSSOP
包裝: 管件
包括: 音頻音調生成,BORSCHT 功能,F(xiàn)SK 生成,振鈴和電池電壓生成
Si3216
Rev. 1.0
47
Not
Recommended
fo
r N
ew
D
esi
gn
s
the command/address byte indicate the address of the
register to be accessed. The second byte of the pair is
the data byte. During a read operation, the SDO
becomes active, and the 8-bit contents of the register
are driven out MSB first. The SDO will be high
impedence on either the falling edge of SCLK following
the LSB or the rising edge of CS, whichever comes first.
SDI is a “don’t care” during the data portion of read
operations. During write operations, data is driven into
the ProSLIC via the SDI pin MSB first. The SDO pin
remains high-impedance during write operations. Data
always transitions with the falling edge of the clock and
is latched on the rising edge. The clock should return to
a logic high when no transfer is in progress.
There are a number of variations of usage on this four-
wire interface:
Continuous clocking. During continuous clocking,
the data transfers are controlled by the assertion of
the CS pin. CS must assert before the falling edge of
SCLK on which the first bit of data is expected during
a read cycle and must remain low for the duration of
the 8 bit transfer (command/address or data).
SDI/SDO wired operation. Independent of the
clocking options described, SDI and SDO can be
treated as two separate lines or wired together if the
master is capable of tristating its output during the
data byte transfer of a read operation.
Daisy chain mode. This mode allows
communication with banks of up to eight ProSLIC
devices using one chip select signal. When the
SPIDC bit in the SPI Mode Select register is set,
data transfer mode changes to a 3-byte operation: a
chip select byte, an address/control byte, and a data
byte. Using the circuit shown in Figure 28, a single
device may select from the bank of devices by
setting the appropriate chip select bit to “1”. Each
device uses the LSB of the chip select byte, shifts
the data right by one bit, and passes the chip select
byte using the SDITHRU pin to the next device in the
chain. Address/control and data bytes are unaltered.
Figure 26. Serial Write 8-Bit Mode
Figure 27. Serial Read 8-Bit Mode
SCLK
CS
SDI
SDO
High Impedance
0
a0
a1
a2
a3
a4
a5
a6
d7
d0
d1
d2
d3
d4
d5
d6
Don't Care
SCLK
CS
SDI
SDO
1
a0
a1
a2
a3
a4
a5
a6
d7
d0
d1
d2
d3
d4
d5
d6
Don't Care
High Impedance
Don't Care
相關PDF資料
PDF描述
VI-21Z-IW-F3 CONVERTER MOD DC/DC 2V 40W
VI-21Z-IW-F2 CONVERTER MOD DC/DC 2V 40W
VI-2T2-IY-F4 CONVERTER MOD DC/DC 15V 50W
VI-2T1-IY-F4 CONVERTER MOD DC/DC 12V 50W
VE-BNK-IY-B1 CONVERTER MOD DC/DC 40V 50W
相關代理商/技術參數
參數描述
SI3216-C-FTR 功能描述:電信線路管理 IC Sng-CH WB SLIC/Codec BJT/inductor dc-dc RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray
SI3216-C-GM 功能描述:電信線路管理 IC Single-Channel Wide- band SLIC/Codec RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray
SI3216-C-GMR 功能描述:電信線路管理 IC Sng-CH WB SLIC/Codec BJT/inductor dc-dc RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray
SI3216DCQ1-EVB 功能描述:子卡和OEM板 Si3216 QFN DAUGHTER CARD RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit
SI3216DCQX-EVB 功能描述:子卡和OEM板 Si3216 QFN DAUGHTER CARD RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit