- 您現在的位置：買賣IC網 > PDF目錄372194 > SP1674BS 12-Bit Sampling A/D Converters PDF資料下載
參數資料
| 型號： | SP1674BS |
| 元件分類： | 串行ADC |
| 英文描述： | 12-Bit Sampling A/D Converters |
| 中文描述： | 12位采樣的A / D轉換器 |
| 文件頁數： | 6/15頁 |
| 文件大?。?/td> | 172K |
| 代理商： | SP1674BS |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁
SP574B/674B/1674B/774B
12–Bit Sampling A/D Converters
6
Copyright 2000 Sipex Corporation
SAMPLE–AND–HOLD FUNCTION
Although there is no sample–and–hold circuit in
the classical sense, the sampling nature of the
capacitive DAC makes the
SPx74B
appear to have
a built–in sample–and–hold. The sample–and–
hold function of the CDAC architecture is opti-
mized to provide full Nyquist sampling at any
maximum sampling rate. Because the S/H func-
tion is included in the ADC circuitry, the majority
of the S/H specifications are included within the A/
D specifications.
Note that some system architectures may use an
external sample–and–hold. The built–in S/H func-
tion of the
SPx74B
will provide additional isola-
tion. Once the internal sample is taken by the
CDAC capacitance, the input of the
SPx74B
is
disconnected from the input. This prevents tran-
sients occurring during conversion from being
inflicted upon the attached buffer. All other 574/
674–type circuits will cause a transient load cur-
rent on the input which will upset the buffer output
and may add error to the conversion itself. In
addition, the isolation of the input after the acqui-
sition time in the
SPx74B
allows you the opportu-
nity to release the HOLD on an external sample–
and–hold and start it tracking the next sample. This
will increase system throughput with your existing
components.
When using an external S/H, the
SPx74B
acts as
any other 574–type device because the internal S/
H is transparent. The sample/hold function in the
SPx74B
is inherent to the capacitor DAC struc-
ture, and its timing characteristics are determined
by the internally generated clock. However, for
multiplexer operation, the internal S/H may elimi-
nate the need for an external S/H. The operation of
the S/H function is internal to the
SPx74B
and is
USING THE SPX74B SERIES
Typical Interface Circuit
The
SPx74B
is a complete A/D converter that is
fully operational when powered up and issued a
Start Convert Signal. Only a few external compo-
nents are necessary. The
SPx74B Series
have four
standard input ranges: 0V to +10V, 0V to +20V,
±
5V and
±
10V.
Figure 2
depicts a typical interface
circuit for operating the
SPx74B
in a unipolar
input mode.
Figure 3
depicts a typical interface
circuit for operating the
SPx74B
in a bipolar input
mode. Further information is given in the follow-
ing sections on these connections, but first a few
considerations concerning board layout to achieve
the best operation.
For each application of this device, strict attention
must be given to power supply decoupling, board
layout (to reduce pickup between analog and digi-
tal sections), and grounding. Digital timing, cali-
bration and the analog signal source must be
considered for correct operation.
To achieve specified accuracy, a double–sided
printed circuit board with a copper ground plane
on the component side is recommended. Keep
analog signal traces away from digital lines. It is
best to lay the PC board out such that there is an
analog section and a digital section with a single
point ground connection between the two through
an RF bead. If this is not possible, run analog
controlled through the normal R/C control line
(refer to
Figure 1
). When the R/C line makes a
negative transition, the
SPx74B
starts the timing
of the sampling and conversion. The first two
clock cycles are allocated to signal acquisition of
the input by the CDAC (this time is defined as
t
). Following these two cycles, the input sample
is taken and held. The A/D conversion follows this
cycle with the duration controlled by the internal
clock cycle, which is determined by the specific
product model. Note that because the sample is
taken relative to the R/C transition, t
is also the
traditional “aperture delay” of this internal sample
and hold. Since t
is measured in clock cycles,
its duration will vary with the internal clock fre-
quency.
Offset, gain and linearity errors of the S/H circuit,
as well as the effects of its droop rate, are included
in the overall specs for the
SPx74B
.
R/C
CE
COWAIT FOR
BUS READ
CONVERSION
VIN
CDAC VOLTAGE
0 VOLTS
t(ACQ)
ACTIME
ACQUISITION TIME =
Figure 1. Sample–and–Hold Function
相關PDF資料 |
PDF描述 |
|---|---|
| SP1674BT | 12-Bit Sampling A/D Converters |
| SP1674B | 12-Bit Sampling A/D Converters(12位采樣A/D轉換器) |
| SP674B | 12-Bit Sampling A/D Converters(12位采樣A/D轉換器) |
| SP774B | 12-Bit Sampling A/D Converters(12位采樣A/D轉換器) |
| SP7800 | 12-Bit 3ms Sampling A/D Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SP1674BT | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:12-Bit Sampling A/D Converters |
| SP1680 | 制造商:SECOS 制造商全稱:SeCoS Halbleitertechnologie GmbH 功能描述:16.0AMP Schottky Barrier Rectifiers |
| SP1690-58 | 制造商:Rostra 功能描述:DIE SET RG213/214 |
| SP1694 | 制造商:SL Power Electronics 功能描述:- Bulk |
| SP16DRA | 制造商:OMRON Industrial Automation 功能描述: 制造商:Omron Corporation 功能描述:PROGRAMMABLE LOGIC CONTROLLER, Leaded Process Compatible:No, Peak Reflow Compati |
發布緊急采購，3分鐘左右您將得到回復。