- 您現在的位置：買賣IC網 > PDF目錄372173 > SP232ECN 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors PDF資料下載
參數資料
| 型號： | SP232ECN |
| 元件分類： | RS-232 |
| 英文描述： | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| 中文描述： | 5V的高速RS - 232收發(fā)器與0.1uF電容 |
| 文件頁數： | 10/15頁 |
| 文件大小： | 126K |
| 代理商： | SP232ECN |
Rev. 06/20/02
SP202E Series High Performance RS232 Transceivers
Copyright 2002 Sipex Corporation
10
SP202E
Family
HUMAN BODY
MODEL Air Discharge Direct Contact Level
IEC1000-4-2
Driver Outputs
Receiver Inputs
±
15kV
±
15kV
±
15kV
±
15kV
±
8kV
±
8kV
4
4
Figure 11. ESD Test Waveform for IEC1000-4-2
t=0ns
t=30ns
0A
15A
30A
t
i
Table 2. Transceiver ESD Tolerance Levels
discharge current rather than the discharge
voltage. Variables with an air discharge such as
approach speed of the object carrying the ESD
potential to the system and humidity will tend to
change the discharge current. For example, the
rise time of the discharge current varies with the
approach speed.
The Contact Discharge Method applies the ESD
current directly to the EUT. This method was
devised to reduce the unpredictability of the
ESD arc. The discharge current rise time is
constant since the energy is directly transferred
without the air-gap arc. In situations such as
hand held systems, the ESD charge can be directly
discharged to the equipment from a person already
holding the equipment. The current is transferred
on to the keypad or the serial port of the equipment
directly and then travels through the PCB and
finally to the IC.
The circuit models in
Figures 9
and
10
represent
the typical ESD testing circuit used for all three
methods. The C
S
is initially charged with the DC
power supply when the first switch (SW1) is on.
Now that the capacitor is charged, the second
switch (SW2) is on while SW1 switches off. The
voltage stored in the capacitor is then applied
through R
S
, the current limiting resistor, onto the
device under test (DUT). In ESD tests, the SW2
switch is pulsed so that the device under test
receives a duration of voltage.
For the Human Body Model, the current limiting
resistor (R
) and the source capacitor (C
) are
1.5k
an 100pF, respectively. For IEC-1000-4-
2, the current limiting resistor (R
) and the source
capacitor (C
S
) are 330
an 150pF, respectively.
The higher C
value and lower R
value in the
IEC1000-4-2 model are more stringent than the
Human Body Model. The larger storage capacitor
injects a higher voltage to the test point when
SW2 is switched on. The lower current limiting
resistor increases the current charge onto the test
point.
相關PDF資料 |
PDF描述 |
|---|---|
| SP232ECP | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| SP232ECT | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| SP232EEN | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| SP232EEP | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| SP233ECT | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SP232ECN/TR | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:High-Performance RS-232 Line Drivers/Receivers |
| SP232ECN-L | 功能描述:RS-232接口集成電路 RS232 ESD +/-15KV temp 0C to 70C RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| SP232ECN-L/TR | 功能描述:RS-232接口集成電路 +/-15KV 5V SNGL SUPP RS-232 0-70C RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| SP232ECP | 功能描述:RS-232接口集成電路 15KV ESD5V 1xSupply RS232 Drvr/Rcvr RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| SP232ECP-L | 功能描述:RS-232接口集成電路 RS232 ESD +/-15KV temp 0C to 70C RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
發(fā)布緊急采購，3分鐘左右您將得到回復。