- 您現在的位置：買賣IC網 > PDF目錄9691 > SP310ECP-L (Exar Corporation)IC DVR/RCVR RS232 ESD 18PDIP PDF資料下載
參數資料
| 型號： | SP310ECP-L |
| 廠商： | Exar Corporation |
| 文件頁數： | 13/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DVR/RCVR RS232 ESD 18PDIP |
| 產品變化通告： | Interface Product Discontinuation 10/May/2011 |
| 標準包裝： | 21 |
| 類型： | 收發器 |
| 驅動器/接收器數： | 2/2 |
| 規程： | RS232 |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 18-DIP（0.300"，7.62mm） |
| 供應商設備封裝： | 18-PDIP |
| 包裝： | 管件 |
| 其它名稱： | 1016-1062-5 |
Exar Corporation 48720 Kato Road, Fremont CA, 94538 (50)668-7000 www.exar.com SP202E,232E,233E, 30E, 32E_0_0603
6
DESCRiPTion
C is charged from Vcc to prepare it for its next
phase.
Phase 3
Vdd charge store and double: Phase three is
identical to the first phase. The positive termi-
nals of C and C2 are charged from Vcc with
their negative terminals initially connected to
ground. C+ is then connected to ground and
the stored charge from C- is superimposed
onto C2-. Since C2+ is still connected to Vcc
the voltage potential across capacitor C2 is now
2 x Vcc.
Phase 4
Vdd transfer: The fourth phase connects the
negative terminal of C2 to ground and the posi-
tive terminal of C2 to the Vdd storage capacitor.
This transfers the doubled (V+) voltage onto C3.
Meanwhile, capacitor C is charged from Vcc to
prepare it for its next phase.
The clock rate for the charge pump typically op-
erates at greater than 5kHz allowing the pump
to run efficiently with small 0.1uF capacitors. Ef-
ficient operation depends on rapid charging and
discharging of C and C2, therefore capacitors
should be mounted as close as possible to the
IC and have low ESR (equivalent series resis-
tance). Inexpensive surface mount, ceramic ca-
pacitors are ideal for using on charge pump. If
polarized capacitors are used the positive and
negative terminals should be connected as
shown in the typical operating circuit. A diagram
of the individual phases are shown in Figure .
Shutdown (SD) and Enable (En) features for
the SP310E and SP312E
Both the SP30E and SP32E have a shutdown
/ standby mode to conserve power in battery-
powered applications. To activate the shutdown
mode, which stops the operation of the charge
pump, a logic "0" is applied to the appropriate
control line. For the SP30E, this control line is
the ON/OFF (pin 8) input. Activating the shut-
down mode puts the SP30E transmitter and
receiver ouptuts into a high impedance con-
dition. For the SP32E, this control line is the
SHUTDOWN (pin8) input; this also puts the
transmitter outputs in a tri-state mode. The re-
ceiver outputs can be tri-stated seperately dur-
ing normal operation or shutdown by applying a
logic "" on the EN line (pin ).
Wake-Up Feature for the SP312E
The SP32E has a wake-up feature that keeps
the receivers active when the device is placed
into shutdown. Table 1 defines the truth table for
the Wake-Up function. When only the receivers
are activated, the SP32E typically draws less
than 5uA supply current. In the case of when
a modem is interfaced to a computer in power
down mode, the Ring Indicator (RI) signal from
the modem would be used to "wake-up" the
computer, allowing it to accept data transmis-
sion.
After the ring indicator has propagated
through the SP32E receiver, it can be used
to trigger the power management circuitry of
the computer to power up the microproces-
sor, and bring the SD pin of the SP32E to a
logic high, taking it out of the shutdown mode.
The receiver propagation delay is typically
us. The enable time for V+ and V- is typi-
cally 2ms. After V+ and V- have settled to their
final values, a signal can be sent back to the
modem on the data terminal ready (DTR) pin
signifying that the computer is ready to accept
the transmit data.
SD EN
Power
Up/Down
Receiver
outputs
0
Down
Enabled
0
Down
Tri-state
0
Up
Enabled
Up
Tri-state
Table . Wake-up Function truth table
Pin Strapping for the SP233E
To operate properly, the following pairs of pins
must be externally wired together as noted in
table 2:
Pins Wired
Together
SOICW
Two V- pins
0 & 7
Two C2+ pins
2 & 5
Two C- pins
& 6
Connect Pins 6 and 9 to
GND
Table 2. Pin Strapping table for SP233E
相關PDF資料 |
PDF描述 |
|---|---|
| VE-JT3-MX-F1 | CONVERTER MOD DC/DC 24V 75W |
| D38999/26WF28SA | CONN PLUG 28POS STRAIGHT W/SCKT |
| MS27484E24A61S | CONN PLUG 61POS STRAIGHT W/SCKT |
| VE-J5Z-EY-F4 | CONVERTER MOD DC/DC 2V 20W |
| VE-J5Z-EY-F3 | CONVERTER MOD DC/DC 2V 20W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SP310ECT | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:High-Performance RS-232 Line Drivers/Receivers |
| SP310ECT/TR | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:High-Performance RS-232 Line Drivers/Receivers |
| SP310ECT-L | 功能描述:RS-232接口集成電路 RS232 w/shutdown temp -40C to 85C RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| SP310ECT-L | 制造商:Exar Corporation 功能描述:IC RS-232 TRANSCEIVER 5.5V WSOIC-18 制造商:Exar Corporation 功能描述:IC, RS-232 TRANSCEIVER, 5.5V, WSOIC-18 |
| SP310ECT-L/TR | 功能描述:RS-232接口集成電路 5V SNGL SUPPLY RS-232 -40-85C RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
發布緊急采購，3分鐘左右您將得到回復。