參數資料
型號： SP3223HCP
英文描述： SOCKET, D, FILTERED, 330PF, 62WAY; Connector type:D Sub, High-Density; Gender:Socket; Ways, No. of:62; Termination method:Solder; Material, contact:Copper Alloy; Plating, contact:Bright Tin; Series:FHTB; Material:Steel; Current RoHS Compliant: Yes
中文描述： 高速智能3.0V至5.5V的RS - 232收發器
文件頁數： 12/23頁
文件大?。?/td> 164K
代理商： SP3223HCP
Rev. 6/30/03
SP3223H +3.0V to +5.5V RS-232 Transceivers
12
Copyright 2003 Sipex Corporation
circuitry is enabled or when in shutdown.
During the shutdown, the receivers will continue
to be active. If there is no activity present at the
receivers for a period longer than 100
μ
s or when
SHUTDOWN is enabled, the device goes into a
standby mode where the circuit draws 1
μ
A.
Driving EN to a logic HIGH forces the outputs of
the receivers into high-impedance. The truth
table logic of the
SP3223H
and
SP3243H
driver
and receiver outputs can be found in
Table 2
.
The
SP3243H
includes an additional non-in-
verting receiver with an output R
OUT. R
OUT
is an extra output that remains active and
monitors activity while the other receiver
outputs are forced into high impedance.
This allows Ring Indicator (RI) from a
peripheral to be monitored without forward
biasing the TTL/CMOS inputs of the other
devices connected to the receiver outputs.
Since receiver input is usually from a transmis-
sion line where long cable lengths and system
interference can degrade the signal, the inputs
have a typical hysteresis margin of 300mV. This
ensures that the receiver is virtually immune to
noisy transmission lines. Should an input be left
unconnected, an internal 5K
pulldown resistor
to ground will commit the output of the receiver
to a HIGH state.
Charge Pump
The charge pump is a
Sipex
–patented design
(U.S. 5,306,954) and uses a unique approach
compared to older less–efficient designs. The
charge pump still requires four external
capacitors, but uses a four–phase voltage
shifting technique to attain symmetrical 5.5V
power supplies. The internal power supply
consists of a regulated dual charge pump that
provides output voltages 5.5V regardless of the
input voltage (V
) over the +3.0V to +5.5V
range. This is important to maintain compliant
RS-232 levels regardless of power supply
fluctuations.
The charge pump operates in a discontinuous
mode using an internal oscillator. If the output
voltages are less than a magnitude of 5.5V, the
charge pump is enabled. If the output voltages
exceed a magnitude of 5.5V, the charge pump is
disabled. This oscillator controls the four phases
of the voltage shifting. A description of each
phase follows.
Phase 1
— V
charge storage — During this phase of
the clock cycle, the positive side of capacitors
C
and C
are initially charged to V
. C
l
then switched to GND and the charge in C
transferred to C
V
, the voltage potential across capacitor C
2
is
now 2 times V
CC
.
+
is
–
is
–
. Since C
+
is connected to
Phase 2
— V
transfer — Phase two of the clock
connects the negative terminal of C
to the V
SS
storage capacitor and the positive terminal of C
2
to GND. This transfers a negative generated
voltage to C
. This generated voltage is
regulated to a minimum voltage of -5.5V.
Simultaneous with the transfer of the voltage to
C
, the positive side of capacitor C
is switched
to V
CC
and the negative side is connected to
GND.
Phase 3
— V
charge storage — The third phase of the
clock is identical to the first phase — the charge
transferred in C
produces –V
in the negative
terminal of C
, which is applied to the negative
side of capacitor C
. Since C
voltage potential across C
2
is 2 times V
CC
.
+
is at V
CC
, the
Phase 4
— V
transfer — The fourth phase of the clock
connects the negative terminal of C
to GND,
and transfers this positive generated voltage
across C
to C
, the V
storage capacitor. This
voltage is regulated to +5.5V. At this voltage,
the internal oscillator is disabled. Simultaneous
with the transfer of the voltage to C
, the
positive side of capacitor C
is switched to V
and the negative side is connected to GND,
allowing the charge pump cycle to begin again.
The charge pump cycle will continue as long as
the operational conditions for the internal
oscillator are present.
相關PDF資料
PDF描述
SP3243H 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors
SP3223H 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors
SP3223HCY SOCKET, 4WAY; Connector type:Rectangular; Gender:Socket; Ways, No. of:4; Termination method:Solder; Material, contact:Copper Alloy; Plating, contact:Silver; Connector insert type:Female; Contact style:Socket; Colour:Green; Insulation RoHS Compliant: Yes
SP3243HCA 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors
SP3243HCT 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors
相關代理商/技術參數
參數描述
SP3223HCY 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:High Speed Intelligent +3.0V to +5.5V RS-232 Transceivers
SP3223U 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Intelligent +3.0V to +5.5V RS-232 Transceivers
SP3223UCA 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:High Speed Intelligent +3.0V to +5.5V RS-232 Transceivers
SP3223UCA/TR 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:High Speed Intelligent +3.0V to +5.5V RS-232 Transceivers
SP3223UCP 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:High Speed Intelligent +3.0V to +5.5V RS-232 Transceivers
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*