參數資料
| 型號： | SP3232EHCA-L |
| 廠商： | Exar Corporation |
| 文件頁數： | 5/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC TXRX RS232 ESD 16SSOP |
| 產品變化通告： | Interface Product Discontinuation 10/May/2011 |
| 標準包裝： | 77 |
| 類型： | 收發(fā)器 |
| 驅動器/接收器數： | 2/2 |
| 規(guī)程： | RS232 |
| 電源電壓： | 3 V ~ 5.5 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 16-SSOP |
| 包裝： | 管件 |
Exar Corporation 48720 Kato Road, Fremont CA, 94538 510-668-7017 www.exar.com
SP3232EH_102_031413
13
DEVICE PIN
HUMAN BODY
IEC61000-4-2
TESTED
MODEL
Air Discharge
Direct Contact
Level
Driver Outputs
+15kV
+8kV
4
Receiver Inputs
+15kV
+8kV
4
equipment from a person already holding
the equipment. The current is transferred
on to the keypad or the serial port of the
equipment directly and then travels through
the PCB and finally to the IC.
The circuit models in Figures 14 and 15 rep-
resent the typical ESD testing circuit used for
all three methods. The C
S is initially charged
with the DC power supply when the first
switch (SW1) is on. Now that the capacitor
is charged, the second switch (SW2) is on
while SW1 switches off. The voltage stored
in the capacitor is then applied through R
S,
the current limiting resistor, onto the device
under test (DUT). In ESD tests, the SW2
switch is pulsed so that the device under
test receives a duration of voltage.
For the Human Body Model, the current
limitingresistor(R
S) and the source capacitor
(C
S) are 1.5k an 100pF, respectively. For
IEC-61000-4-2, the current limiting resistor
(R
S) and the source capacitor (CS) are 330
an 150pF, respectively.
Figure 16. ESD Test Waveform for IEC61000-4-2
Figure 15. ESD Test Circuit for IEC61000-4-2
Table 2. Transceiver ESD Tolerance Levels
RS and RV add up to 330 for IEC61000-4-2.
RC
Device
Under
Test
DC Power
Source
CS
RS
SW1
SW2
RV
Contact-Discharge Model
t = 0ns
t = 30ns
0A
15A
30A
I→
t →
The higher C
S value and lower RS value in
the IEC61000-4-2 model are more stringent
than the Human Body Model. The larger
storage capacitor injects a higher voltage
to the test point when SW2 is switched on.
The lower current limiting resistor increases
the current charge onto the test point.
DESCRIPTION
相關PDF資料 |
PDF描述 |
|---|---|
| MS3111E20-16P | CONN RCPT 16POS CBL MNT W/PINS |
| D38999/20FH53SC | CONN RCPT 53POS WALL MNT W/SCKT |
| MS27467T15B35SD | CONN PLUG 37POS STRAIGHT W/SCKT |
| GTC06CF-16-12P | CONN PLUG 1POS STRAIGHT W/PINS |
| M83723/83R1404N | CONN RCPT 4POS WALL MT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SP3232EHCA-L/TR | 功能描述:RS-232接口集成電路 3.3V 460KBPS RS-232 RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| SP3232EHCP | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:3.3V, 460 Kbps RS-232 Transceivers |
| SP3232EHCP-L | 功能描述:RS-232接口集成電路 3.3V 460KBPS RS-232 RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| SP3232EHCT | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:3.3V, 460 Kbps RS-232 Transceivers |
| SP3232EHCT/TR | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:3.3V, 460 Kbps RS-232 Transceivers |
發(fā)布緊急采購，3分鐘左右您將得到回復。