- 您現在的位置：買賣IC網 > PDF目錄372179 > SP3243EHCT 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors PDF資料下載
參數資料
| 型號： | SP3243EHCT |
| 元件分類： | RS-232 |
| 英文描述： | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| 中文描述： | 5V的高速RS - 232收發器與0.1uF電容 |
| 文件頁數： | 17/25頁 |
| 文件大?。?/td> | 279K |
| 代理商： | SP3243EHCT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁
17
Date: 6/2/04
SP3223EB/3243EB +3.0V to +5.5V RS-232 Transceivers
Copyright 2004 Sipex Corporation
AUTO ON-LINE
Circuitry
The SP3223EB and SP3243EB devices have a
patent pending AUTO ON-LINE
circuitry on
board that saves power in applications such as
laptop computers, palmtop (PDA) computers,
and other portable systems.
The SP3223EB and SP3243EB devices incorpo-
rate an AUTO ON-LINE
circuit that automati-
cally enables itself when the external transmit-
ters are enabled and the cable is connected.
Conversely, the AUTO ON-LINE
circuit also
disables most of the internal circuitry when the
device is not being used and goes into a standby
mode where the device typically draws 1
μ
A.
This function can also be externally controlled
by the ONLINE pin. When this pin is tied to a
logic LOW, the AUTO ON-LINE
function is
active. Once active, the device is enabled until
there is no activity on the receiver inputs. The
receiver input typically sees at least
±
3V, which
are generated from the transmitters at the other
end of the cable with a
±
5V minimum. When the
external transmitters are disabled or the cable is
disconnected, the receiver inputs will be pulled
down by their internal 5k
resistors to ground.
When this occurs over a period of time, the
internal transmitters will be disabled and the
device goes into a shutdown or standby mode.
When ONLINE is HIGH, the AUTO ON-LINE
mode is disabled.
The AUTO ON-LINE
circuit has two stages:
1) Inactive Detection
2) Accumulated Delay
The first stage, shown in
Figure 28
, detects an
inactive input. A logic HIGH is asserted on
R
X
INACT if the cable is disconnected or the
external transmitters are disabled. Otherwise,
R
X
INACT will be at a logic LOW. This circuit is
duplicated for each of the other receivers.
The second stage of the AUTO ON-LINE
cir-
cuitry, shown in
Figure 29
, processes all the
receiver's R
X
INACT signals with an accumu-
lated delay that disables the device to a 1
μ
A
supply current.
The STATUS pin goes to a logic LOW when the
cable is disconnected, the external transmitters
are disabled, or the SHUTDOWN pin is
invoked. The typical accumulated delay is
around 20
μ
s.
When the SP3223EB and SP3243EB drivers or
internal charge pump are disabled, the supply
current is reduced to 1
μ
A. This can commonly
occur in hand-held or portable applications where
the RS-232 cable is disconnected or the RS-232
drivers of the connected peripheral are turned off.
The AUTO ON-LINE
mode can be disabled by
the SHUTDOWN pin. If this pin is a logic LOW,
the AUTO ON-LINE
function will not operate
regardless of the logic state of the ONLINE pin.
Table 3 summarizes the logic of the AUTO ON-
LINE
operating modes. The truth table logic of
the SP3223EB and SP3243EB driver and re-
ceiver outputs can be found in Table 2.
The STATUS pin outputs a logic LOW signal
if the device is shutdown. This pin goes to a
logic HIGH when the external transmitters are
enabled and the cable is connected.
When the SP3223EB and SP3243EB devices
are shut down, the charge pumps are turned off.
V+ charge pump output decays to V
CC
, the
V- output decays to GND. The decay time will
depend on the size of capacitors used for the
charge pump. Once in shutdown, the time
required to exit the shut down state and have
valid V+ and V- levels is typically 200
μ
s.
For easy programming, the STATUS can be
used to indicate DTR or a Ring Indicator signal.
Tying ONLINE and SHUTDOWN together
will bypass the AUTO ON-LINE
circuitry so
this connection acts like a shutdown input pin.
相關PDF資料 |
PDF描述 |
|---|---|
| SP3249ECA | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| SP3249E | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| SP3249ECY | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| SP3249EEA | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| SP3249EEY | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SP3243EHCT-L | 功能描述:RS-232接口集成電路 RS232 460 kbps temp 0C to 70C RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| SP3243EHCT-L/TR | 功能描述:RS-232接口集成電路 Intel. +3V to +5.5V RS-232 RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| SP3243EHEA-L | 功能描述:RS-232接口集成電路 Intel. +3V to +5.5V RS-232 RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| SP3243EHEA-L/TR | 功能描述:RS-232接口集成電路 Intel. +3V to +5.5V RS-232 RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| SP3243EHET | 功能描述:RS-232接口集成電路 Intelligent 3-5.5V RS-232 Transceiver RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
發布緊急采購，3分鐘左右您將得到回復。