參數資料
型號： SP333CT
元件分類： RS-232
英文描述： 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors
中文描述： 5V的高速RS - 232收發器與0.1uF電容
文件頁數： 8/13頁
文件大?。?/td> 175K
代理商： SP333CT
8
TGoddard/SP333/9617R0
SP333 RS-232/AppleTalk Programmable Transceiver
Copyright 2000 Sipex Corporation
Phase 1
-Vss charge storage- During this phase of the
clock cycle, the positive side of capacitors C1
and C2 are initially charged to +5V. C1+ is then
switched to ground and charge in C1- is trans-
ferred to C2-. Since C2+ is connected to +5V,
the voltage potential across capacitor C2 is
now 10V.
Phase 2
-Vss transfer- Phase two of the clock connects
the negative terminal of C2 to the Vss storage
capacitor and the positive terminal of C2 to
ground, and transfers the generated -10V to C3.
Simultaneously, the positive side of capacitor
C1 is switched to +5V and the negative side is
connected to ground.
Phase 3
-Vdd charge storage- The third phase of the
clock is identical to the first phase- the trans-
ferred charge in C1 produces -5V in the negative
terminal of C1, which is applied to the negative
side of capacitor C2. Since C2+ is at +5V, the
voltage potential across C2 is 10V.
Phase 4
-Vdd transfer- The fourth phase of the clock
connects the negative terminal of C2 to ground
and transfers the generated 10V across C2 to C4,
the Vdd storage capacitor. Simultaneously with
this, the positive side of capacitor C1 is switched
to +5V and the negative side is connected to
ground, and the cycle begins again.
Since both V+ and V- are separately generated
from Vcc in a no load condition, V+ and V- will
be symmetrical. Older charge pump approaches
that generate V- from V+ will show a decrease
in the magnitude of V- compared to V+ due to
the inherent inefficiencies in the design.
The clock rate for the charge pump typically
operates at 15kHz. The external capacitors should
be 0.1
μ
F with a 16V breakdown rating.
External Power Supplies
For applications that do not require +5V only,
external supplies can be applied at the V+ and
V- pins. The value of the external supply volt-
ages must be no greater than
±
10V. The current
drain from the
±
10V supplies is used for the RS-
232 drivers. For the RS-232 driver, the current
requirement is 3.5mA per driver. The external
power supplies should provide a power supply
sequence of either: +10V, –10V, and then +5V;
or –10V, +10V, and then +5V. It is critical that
the
±
10V supplies are on before V
CC
.
Figure 11. Charge Pump Waveforms
–10V
b) C
2
–
GND
GND
a) C
2
+
+10V
相關PDF資料
PDF描述
SP334 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors
SP334CT 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors
SP334ET 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors
SP3481 Cermet Potentiometer; Resistance Max:10kohm; Resistance Tolerance:+/- 10 %; Power Rating:1W; Voltage Rating:350V; Series:149; Temperature Coefficient:+/-150 ppm; Resistor Element Material:Cermet; Leaded Process Compatible:Yes
SP3481CN +3.3V Low Power Half-Duplex RS-485 Transceivers with 10Mbps Data Rate
相關代理商/技術參數
參數描述
SP333ET 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:+5V Only RS-232/AppleTalk⑩ Programmable Transceiver
SP334 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Programmable RS-232/RS-485 Transceiver
SP3345ABAOPM 制造商:Rochester Electronics LLC 功能描述:- Bulk
SP3345ACA0PMR 制造商:Rochester Electronics LLC 功能描述:SERVO DEMOD W/ AGC + FILTER - Bulk
SP334CT 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Programmable RS-232/RS-485 Transceiver
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*