- 您現在的位置：買賣IC網 > PDF目錄372186 > SP6123A Low Voltage, Synchronous Step-Down PWM Controller Ideal for 2A to 10A, Small Footprint, DC-DC Power Converters PDF資料下載
參數資料
| 型號： | SP6123A |
| 英文描述： | Low Voltage, Synchronous Step-Down PWM Controller Ideal for 2A to 10A, Small Footprint, DC-DC Power Converters |
| 中文描述： | 低，同步降壓電壓降壓PWM控制器，適合2A至10A條，占地面積小，DC - DC電源轉換器 |
| 文件頁數： | 12/18頁 |
| 文件大?。?/td> | 154K |
| 代理商： | SP6123A |
12
Date: 5/25/04
SP6123 Low Voltage, Synchronous Step Down PWM Controller Copyright 2004 Sipex Corporation
V
GS
. For 5V input, use the R
DS(ON)
specified at
4.5V V
GS
. At the time of this publication, ven-
dors, such as Fairchild, Siliconix and Interna-
tional Rectifier, have started to specify R
DS(ON)
at V
GS
less than 3V. This data is necessary for
designs where the MOSFETs are driven with
3.3V.
Thermal calculation must be conducted to en-
sure the MOSFET can handle the maximum
load current. The junction temperature of the
MOSFET, determined as follows, must stay
below the maximum rating.
JA
MOSFET
R
A
J
P
T
T
θ
(max)
(max)
(max)
+
=
,
where
T
A(max)
= maximum ambient temperature
P
MOSFET(max)
= maximum power dissipation of
the MOSFET
R
θ
JA
= junction to ambient thermal resistance.
R
JA
of the device depends greatly on the board
layout, as well as device package. Significant
thermal improvement can be achieved in the maxi-
mum power dissipation through the proper design
of copper mounting pads on the circuit board. For
example, in a SO-8 package, placing two 0.04
square inches copper pad directly under the pack-
age, without occupying additional board space,
can increase the maximum power dissipation from
approximately 1 to 1.2W. For DPAK package,
enlarging the tap mounting pad to 1 square inches
reduces the R
θ
JA
from 96
°
C/W to 40
°
C/W.
Schottky Diode Selection
When paralleled with the bottom MOSFET, an
optional Schottky diode can improve efficiency
and reduce noise. Without this Schottky diode,
the body diode of the bottom MOSFET con-
ducts the current during the non-overlap time
when both MOSFETs are turned off. Unfortu-
nately, the body diode has high forward voltage
and reverse recovery problem. The reverse re-
covery of the body diode causes additional
switching noises when the diode turns off. The
Schottky diode alleviates this noise and addi-
tionally improves efficiency thanks to its low
forward voltage. The reverse voltage across the
diode is equal to input voltage, and the diode
must be able to handle the peak current equal to
the maximum load current.
The power dissipation of the Schottky diode is
determined by
P
DIODE
= 2V
F
I
OUT
T
NOL
F
S
where
T
NOL
= non-overlap time between G
L
and G
H
.
V
F
= forward voltage of the Schottky diode.
SP6123
C2
C1
R1
COMP
Figure 1. The RC network connected to the COMP pin
provides a pole and a zero to control loop.
Loop Compensation Design
The goal of loop compensation is to manipulate
loop frequency response such that its gain crosses
over 0db at a slope of -20db/dec. The SP6123
has a transconductance error amplifier and re-
quires the compensation network to be con-
nected between the COMP pin and ground, as
shown in Figure 1.
The first step of compensation design is to pick
the loop crossover frequency. High crossover
frequency is desirable for fast transient response,
but often jeopardize the system stability. Cross-
over frequency should be higher than the ESR
zero but less than 1/5 of the switching fre-
quency. The ESR zero is contributed by the ESR
associated with the output capacitors and can be
determined by
f
Z(ESR)
=
1
2
π
C
OUT
R
ESR
Crossover frequency of 20kHz is a sound first
try if low ESR tantalum capacitors or POSCAPs
are used at the output. The next step is to calcu-
late the complex conjugate poles contributed by
the LC output filter,
APPLICATIONS INFORMATION
相關PDF資料 |
PDF描述 |
|---|---|
| SP6123 | Low Voltage, Synchronous Step-Down PWM Controller Ideal for 2A to 10A, Small Footprint, DC-DC Power Converters |
| SP6125 | High-Voltage, Step Down Controller in TSOT6 |
| SP6125EK1L | High-Voltage, Step Down Controller in TSOT6 |
| SP6126_1 | Evaluation Board Manual |
| SP6126EB | Evaluation Board Manual |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SP6123ACN | 制造商:Exar Corporation 功能描述:Swithed-Mode Power Supply Controller, Voltage Mode Type, 8 Pin, Plastic, SOP |
| SP6123ACN/TR | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Low Voltage, Synchronous Step-Down PWM Controller Ideal for 2A to 10A, Small Footprint, DC-DC Power Converters |
| SP6123ACN-L | 功能描述:電壓模式 PWM 控制器 Low Voltage, Micro 8 Synchronous, Cntrllr RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| SP6123ACN-L/TR | 功能描述:電壓模式 PWM 控制器 Low Voltage, Micro 8 Synchronous, Cntrllr RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| SP6123AEN-L | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。