- 您現在的位置：買賣IC網 > PDF目錄372186 > SP6123ACN CAP .033UF 100V PPS FILM ECH-S PDF資料下載
參數資料
| 型號： | SP6123ACN |
| 英文描述： | CAP .033UF 100V PPS FILM ECH-S |
| 中文描述： | 低，同步降壓電壓降壓PWM控制器，適合2A至10A條，占地面積小，DC - DC電源轉換器 |
| 文件頁數： | 16/18頁 |
| 文件大小： | 154K |
| 代理商： | SP6123ACN |
16
Date: 5/25/04
SP6123 Low Voltage, Synchronous Step Down PWM Controller Copyright 2004 Sipex Corporation
PCB layout plays a critical role in proper func-
tion of the converters and EMI control. In switch
mode power supplies, loops carrying high di/dt
give rise to EMI and ground bounces. The goal
of layout optimization is to identify these loops
and minimize them. It is also crucial on how to
connect the controller ground such that its op-
eration is not affected by noise. The following
guideline should be followed to ensure proper
operation.
1. A ground plane is recommended for minimiz-
ing noises, copper losses and maximizing heat
dissipation.
2. Begin the layout by placing the power compo-
nents first. Orient the power circuitry to achieve
a clean power flow path. If possible make all the
connections on one side of the PCB with wide,
copper filled areas.
3. Connect the ground of feedback divider and
compensation components directly to the GND
pin of the IC using a dedicated ground trace.
Then connect this pin as close as possible to the
ground of the output capacitor.
4. The V
CC
bypass capacitor should be right next
to the V
CC
and GND pins.
5. The trace connecting the feedback resistors to
the output should be short, direct and far away
from the switch node, and switching compo-
nents.
6. Minimize the trace between G
H
/G
L
and the
gates of the MOSFETs to reduce the impedance
driving the MOSFETs. This is especially impor-
tant for the bottom MOSFET that tends to turn
on through its Miller capacitor when the switch
node swings high.
7. Minimize the loop composed of input capaci-
tors, top/bottom MOSFETs and Schottky diode.
This loop carries high di/dt current. Also in-
crease the trace width to reduce copper losses.
8. Maximize the trace width of the loop connect-
ing the inductor, output capacitors, Schottky
diode and bottom MOSFET.
LAYOUT GUIDELINE
相關PDF資料 |
PDF描述 |
|---|---|
| SP6123CN | CAP .01UF 50V PPS FILM ECH-S |
| SP6123A | Low Voltage, Synchronous Step-Down PWM Controller Ideal for 2A to 10A, Small Footprint, DC-DC Power Converters |
| SP6123 | Low Voltage, Synchronous Step-Down PWM Controller Ideal for 2A to 10A, Small Footprint, DC-DC Power Converters |
| SP6125 | High-Voltage, Step Down Controller in TSOT6 |
| SP6125EK1L | High-Voltage, Step Down Controller in TSOT6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SP6123ACN/TR | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Low Voltage, Synchronous Step-Down PWM Controller Ideal for 2A to 10A, Small Footprint, DC-DC Power Converters |
| SP6123ACN-L | 功能描述:電壓模式 PWM 控制器 Low Voltage, Micro 8 Synchronous, Cntrllr RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| SP6123ACN-L/TR | 功能描述:電壓模式 PWM 控制器 Low Voltage, Micro 8 Synchronous, Cntrllr RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| SP6123AEN-L | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
| SP6123CN | 制造商:Exar Corporation 功能描述:Swithed-Mode Power Supply Controller, Voltage Mode Type, 8 Pin, Plastic, SOP |
發布緊急采購，3分鐘左右您將得到回復。