- 您現在的位置：買賣IC網 > PDF目錄372186 > SP6126_1 Evaluation Board Manual PDF資料下載
參數資料
| 型號： | SP6126_1 |
| 英文描述： | Evaluation Board Manual |
| 中文描述： | 評估板手冊 |
| 文件頁數： | 2/8頁 |
| 文件大?。?/td> | 386K |
| 代理商： | SP6126_1 |
2
USING THE EVALUATION BOARD
1) Powering Up the SP6126EB Circuit
Connect the SP6126 Evaluation Board
to an external +12V power supply. Connect with
short leads directly to the “VIN” and “GND” posts. Connect a Load between the “VOUT”
and “GND” posts, again using short leads to minimize inductance and voltage drop.
2) Measuring Output Load Characteristics
It’s best to GND reference scope and digital meters using the Star GND post near the
output of the board. VOUT ripple can best be seen touching probe tip to the pad for
COUT and scope GND collar touching Star GND post – avoid a GND lead on the scope
which will increase noise pickup.
3)
Using the Evaluation Board with Different Output Voltages
While the SP6126 Evaluation Board has been tested and delivered with the output set
to 3.30V, by simply changing one resistor, R2, the SP6126 can be set to other output
voltages. The relationship in the following formula is based on a voltage divider from the
output to the feedback pin FB, which is set to an internal reference voltage of 0.60V.
Standard 1% metal film resistors of surface mount size 0603 are recommended.
1
2
Vout
=
1
Vref
R
R
Where R1 = 200k
. For Vout = 0.60V setting, simply remove R2 from the board.
Note that since the SP6126 Evaluation Board design was optimized for 12V down
conversion to 3.30V, changes of output voltage and/or input voltage will alter
performance from the data given in the Power Supply Data section.
Using the SHDN (ON/OFF function)
Feedback pin serves a dual role of ON/OFF control. The MOSFET driver is disabled
when a voltage greater than 1V is applied at FB pin. Maximum voltage rating of this pin
is 5.5V. The controlling signal should be applied through a small signal diode as shown
on page 1. Under no-load condition an optional 10kOhm bleeding resistor across the
output helps keep the output capacitor discharged.
POWER SUPPLY DATA
The SP6126EB is designed with an accurate 2% reference over line, load and
temperature. Figure 1 data shows a typical SP6126 Evaluation Board efficiency plot,
with efficiencies to 92% and output currents to 2.5A. SP6126 Load Regulation in Figure
2 shows no change in output voltage from no load to 2A load. Figures 3 and 4 show the
transient response of the SP6126. Figures 5 and 6 show a controlled start-up with no
load and 2A load when power is applied where the input current rises smoothly as the
soft-start ramp increases. Figures 7 and 8 show the output ripple under no load and 2A
load.
相關PDF資料 |
PDF描述 |
|---|---|
| SP6126EB | Evaluation Board Manual |
| SP6126EK1 | Evaluation Board Manual |
| SP6126 | High-Voltage, Step Down Controller in TSOT6 |
| SP6126_07 | High-Voltage, Step Down Controller in TSOT6 |
| SP6126EK1L | High-Voltage, Step Down Controller in TSOT6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SP6126EB | 功能描述:電源管理IC開發工具 Eval Board for SP6126 Series RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| SP6126EK1 | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Evaluation Board Manual |
| SP6126EK1L | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:High-Voltage, Step Down Controller in TSOT6 |
| SP6126EK1-L | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| SP6126EK1L/TR | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:High-Voltage, Step Down Controller in TSOT6 |
發布緊急采購，3分鐘左右您將得到回復。