- 您現在的位置：買賣IC網 > PDF目錄372186 > SP6126EK1L High-Voltage, Step Down Controller in TSOT6 PDF資料下載
參數資料
| 型號： | SP6126EK1L |
| 英文描述： | High-Voltage, Step Down Controller in TSOT6 |
| 中文描述： | 高電壓，降壓控制器在TSOT6步 |
| 文件頁數： | 6/14頁 |
| 文件大?。?/td> | 477K |
| 代理商： | SP6126EK1L |
Overcurrent Protection
Mar 29-07 RevD SP6126: TSOT-6 PFET Buck Controller
2007 Sipex Corporation
6
Ds
Q1
Rs
SP6126
Gate
LX
30uA
+
-
Vin - 0.3V
Vin
Over-Current Comparator
Figure 3- Overcurrent protection circuit
The overcurrent protection circuit functions by
monitoring the voltage across the high-side FET
Q1. When this voltage exceeds 0.3V, the
overcurrent
comparator
controller enters hiccup mode. For example if
Q1 has Rds(on)=0.1
, then the overcurrent will
trigger at I = 0.3V/0.1
=3A. To program a lower
overcurrent use a resistor Rs as shown in figure
1. Calculate Rs from:
(
uA
30
The overcurrent circuit triggers at peak current
through Q1 which is usually about 15% higher
than average output current. Hence the
multiplier 1.15 is used in (5).
Example: A switching MOSFET used with
SP6126 has Rds(on) of 0.1
. Program the over-
current circuit so that maximum output is 2A.
(
Rs
=
triggers
and
the
)
on
Rds
Iout
Rs
)
(
15
.
3
×
×
=
…..…… (5)
)
uA
Ohm
A
30
1
×
1
15
.
3
×
Rs = 2333
Using the above equation there is good
agreement between calculated and test results
when an RS in the range of 0.5k to 3k is used.
For RS larger than 3k test results are lower than
those predicted by (5), due to circuit parasitics.
Using the ON/OFF Function
Feedback pin serves a dual role of ON/OFF
control. The MOSFET driver is disabled when a
voltage greater than 1V is applied at FB pin.
Maximum voltage rating of this pin is 5.5V. The
controlling signal should be applied through a
small signal diode as shown on page 1.
Please
note that an optional 10k
bleeding resistor
across the output helps keep the output
capacitor discharged under no load condition.
Programming the Output Voltage
To program the output voltage, calculate R2
using the following equation:
R
R
=
1
1
2
Vref
Vout
Where: Vref=0.6 is the reference voltage of the
SP6126
R1=200k
is a fixed-value resistor that, in
addition to being a voltage divider, it is part of
the compensation network. In order to simplify
compensation calculations, R1 is fixed at 200k
.
Soft Start
Soft Start is preset internally to 5ms (nominal).
Internal Soft Start eliminates the need for the
external capacitor CSS that is commonly used to
program this function.
MOSFET Gate Drive
P-channel drive is derived through an internal
regulator that generates V
IN
-5V. This pin (VDR)
has to be connected to V
IN
with a 0.1uF
decoupling capacitor. The gate drive circuit
swings between V
IN
and V
IN
-5 and employs
powerful drivers for efficient switching of the P-
channel MOSFET.
GENERAL OVERVIEW
相關PDF資料 |
PDF描述 |
|---|---|
| SP6126EK1-L | High-Voltage, Step Down Controller in TSOT6 |
| SP6127_07 | Evaluation Board Manual |
| SP6127EB | Evaluation Board Manual |
| SP6127EK1 | Evaluation Board Manual |
| SP6127EK1L | High-Voltage, Step-Down Controller in TSOT6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SP6126EK1-L | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| SP6126EK1L/TR | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:High-Voltage, Step Down Controller in TSOT6 |
| SP6126EK1-L/TR | 功能描述:電壓模式 PWM 控制器 High-Voltage Step Down Controller RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| SP6127 | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Evaluation Board Manual |
| SP6127_07 | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Evaluation Board Manual |
發布緊急采購，3分鐘左右您將得到回復。