參數資料
型號: SP6132CU
英文描述: Wide Input, 300KHz Synchronous PWM Controller
中文描述: 寬輸入,300kHz的同步PWM控制器
文件頁數: 10/14頁
文件大小: 314K
代理商: SP6132CU
10
Date: 8/4/04
SP6132 Wide Input, 300KHz Synchronous PWM Controller Copyright 2004 Sipex Corporation
thermal improvement can be achieved in the maxi-
mum power dissipation through the proper design
of copper mounting pads on the circuit board. For
example, in a SO-8 package, placing two 0.04
square inches copper pad directly under the pack-
age, without occupying additional board space,
can increase the maximum power from approxi-
mately 1 to 1.2W. For DPAK package, enlarging
the tap mounting pad to 1 square inches reduces the
R
Θ
JA from 96
°
C/W to 40
°
C/W.
APPLICATIONS INFORMATION: Continued
Schottky Diode Selection
When paralleled with the bottom MOSFET, an
optional Schottky diode can improve efficiency
and reduce noises. Without this Schottky diode,
the body diode of the bottom MOSFET con-
ducts the current during the non-overlap time
when both MOSFETs are turned off. Unfortu-
nately, the body diode has high forward voltage
and reverse recovery problem. The reverse re-
covery of the body diode causes additional
switching noises when the diode turns off. The
Schottky diode alleviates these noises and addi-
tionally improves efficiency thanks to its low
forward voltage. The reverse voltage across the
diode is equal to input voltage, and the diode
must be able to handle the peak current equal to
the maximum load current.
The power dissipation of the Schottky diode is
determined by
P
DIODE
= 2V
F
I
OUT
T
NOL
F
S
where
T
NOL
= non-overlap time between GH and GL.
V
F
= forward voltage of the Schottky diode.
Loop Compensation Design
The open loop gain of the whole system can be
divided into the gain of the error amplifier,
PWM modulator, buck converter output stage,
and feedback resistor divider. In order to cross-
over at the selected frequency FCO, the gain of
the error amplifier has to compensate for the
attenuation caused by the rest of the loop at this
frequency.
SP6132 Voltage Mode Control Loop with Loop Dynamic
Definitions:
Resr = Output Capacitor Equivalent Series Resistance
Rdc = Output Inductor DC Resistance
Vramp_pp = SP6132 internal RAMP Amplitude Peak to Peak Voltage
Conditions:
Cz2 >> Cp1 and R1 >> Rz3
Output Load Resistance >> Resr and Rdc
(SRz2Cz2+1)(SR1Cz3+1)
(SR
ESR
C
OUT
+ 1)
[S^2LC
OUT
+S(R
ESR
+R
DC
) C
OUT
+1]
V
IN
SR1Cz2(SRz3Cz3+1)(SRz2Cp1+1)
V
RAMP_PP
V
OUT
(Volts)
+
_
V
REF
(Volts)
Notes: R
ESR
= Output Capacitor Equivalent Series Resistance.
R
DC
= Output Inductor DC Resistance.
V
RAMP_PP
= SP6132 Internal RAMP Amplitude Peak to Peak Voltage.
Condition: Cz2 >> Cp1 & R1 >> Rz3
ESR
& R
DC
R
2
V
REF
V
OUT
(R
1
+ R
2
)
or
V
FBK
(Volts)
Type III Voltage Loop
Compensation
G
AMP
(s) Gain Block
PWM Stage
G
PWM
Gain
Block
Output Stage
G
OUT
(s) Gain
Block
Voltage Feedback
G
FBK
Gain Block
相關PDF資料
PDF描述
SP6132EB Evaluation Board Manual
SP6132EU Wide Input, 300KHz Synchronous PWM Controller
SP6132HV High Voltage Synchronous Buck Controller
SP6133 Evaluation Board Manual
SP6133_06 Evaluation Board Manual
相關代理商/技術參數
參數描述
SP6132CU/TR 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Wide Input, 300KHz Synchronous PWM Controller
SP6132CU-L 功能描述:開關變換器、穩壓器與控制器 Wide Input, 300kHz Synchronous RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel
SP6132CU-L/TR 功能描述:開關變換器、穩壓器與控制器 Wide Input, 300kHz Synchronous RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel
SP6132EB 功能描述:電壓模式 PWM 控制器 Dual Supply Sync Buck Controller RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel
SP6132EU 制造商:Exar Corporation 功能描述:SMPS Controller