- 您現在的位置：買賣IC網 > PDF目錄372187 > SP6134HCU High Voltage, 600 KHz Synchronous PWM Controller PDF資料下載
參數資料
| 型號： | SP6134HCU |
| 英文描述： | High Voltage, 600 KHz Synchronous PWM Controller |
| 中文描述： | 高電壓，600千赫同步PWM控制器 |
| 文件頁數： | 4/14頁 |
| 文件大?。?/td> | 141K |
| 代理商： | SP6134HCU |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁
4
Date: 8/4/04
SP6134H High Voltage, 600KHz Synchronous PWM Controller Copyright 2004 Sipex Corporation
PIN #
1
PIN NAME DESCRIPTION
V
CC
Bias Supply Input. Connect to external 5V supply. Used to power internal circuits and
low side gate driver.
GL
High current driver output for the low side NFET switch. It is always low if GH is high or
during a fault. Resistor pull down ensure low state at low voltage.
GND
Ground Pin. The control circuitry of the IC and lower power driver are referenced to this
pin. Return separately from other ground traces to the (-) terminal of C
OUT
.
V
FB
Feedback Voltage and Short Circuit Detection pin. It is the inverting input of the Error
Amplifier and serves as the output voltage feedback point for the Buck Converter. The
output voltage is sensed and can be adjusted through an external resistor divider.
Whenever V
drops 0.25V below the positive reference, a short circuit fault is detected
and the IC enters hiccup mode.
COMP
Output of the Error Amplifier. It is internally connected to the non-inverting input of the
PWM comparator. An optimal filter combination is chosen and connected to this pin and
either ground or V
FB
to stabilize the voltage mode loop.
UVIN
UVLO input for V
voltage. Connect a resistor divider between V
IN
and UVIN to set
minimum operating voltage.
SS
Soft Start. Connect an external capacitor between SS and GND to set the soft start rate
based on the 10
μ
A source current. The SS pin is held low via a 1mA (min) current during
all fault conditions.
SWN
Lower supply rail for the GH high-side gate driver. Connect this pin to the switching node
at the junction between the two external power MOSFET transistors.
GH
High current driver output for the high side NFET switch. It is always low if GL is high or
during a fault. Resistor pull down ensure low state at low voltage.
BST
High side driver supply pin. Connect BST to the external boost diode and capacitor as
shown in the Typical Application Circuit on page 1. High side driver is connected between
BST pin and SWN pin.
2
3
4
5
6
7
8
9
10
PIN DESCRIPTION
相關PDF資料 |
PDF描述 |
|---|---|
| SP6136 | Evaluation Board Manual |
| SP6136_06 | Evaluation Board Manual |
| SP6136EB | Evaluation Board Manual |
| SP6136ER1 | Evaluation Board Manual |
| SP6137 | Wide Input, 900KHz Synchronous PWM Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SP6134HCU/TR | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Dual Supply Synchronous Buck Controller |
| SP6134HCU-L | 功能描述:開關變換器、穩壓器與控制器 High Voltage,600 kHz Synchronous RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| SP6134HCU-L/TR | 功能描述:開關變換器、穩壓器與控制器 High Voltage,600 kHz Synchronous RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| SP6134HEU | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Dual Supply Synchronous Buck Controller |
| SP6134HEU/TR | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Dual Supply Synchronous Buck Controller |
發布緊急采購，3分鐘左右您將得到回復。