- 您現在的位置：買賣IC網 > PDF目錄372187 > SP6138_06 Evaluation Board Manual PDF資料下載
參數資料
| 型號： | SP6138_06 |
| 英文描述： | Evaluation Board Manual |
| 中文描述： | 評估板手冊 |
| 文件頁數： | 2/9頁 |
| 文件大?。?/td> | 304K |
| 代理商： | SP6138_06 |
Aug 24-06 SP6138 Evaluation Manual 2006 Sipex Corporation
Page 2 of 9
USING THE EVALUATION BOARD
1) Powering Up the SP6138EB Circuit
Connect the SP6138 Evaluation Board
with an external +12V power supply. Connect
with short leads and large diameter wire directly to the “V
IN
” and “G
IN
” posts. Connect a
Load between the “V
O
” and “G
O
” posts, again using short leads with large diameter wire
to minimize inductance and voltage drops.
2) Measuring Output Load Characteristics
It’s best to ground any reference scope and digital meters using the Star GND post in
the center of the board. V
OUT
ripple can best be seen by touching the probe tip to the
pad for C
OUT
and the scope GND collar touching the Star GND post – avoid a GND lead
on the scope which will increase noise pickup.
3)
Using the Evaluation Board with Different Output Voltages
The SP6138 Evaluation Board has been tested and delivered with the output set to
3.30V. By simply changing one resistor, R2, the SP6138 can be set to other output
voltages. The relationship in the following formula is based on a voltage divider from the
output to the feedback pin V
FB
, which is set to an internal reference voltage of 0.80V.
Standard 1% metal film resistors of surface mount size 0603 are recommended.
V
OUT
= 0.80V ( R1 / R2 + 1 ) => R2 = R1 / [ (V
OUT
/ 0.80V ) – 1 ]
Where R1 = 68.1K
and for the V
OUT
= 0.80V setting, simply remove R2 from the
board. Furthermore, one could select the value of R1 & R2 combination to meet the
exact output voltage setting by restricting R1 resistance range such that 50K
≤
R1
≤
100K
for overall system loop stability.
Note that since the SP6138 Evaluation Board design was optimized for 12V down
conversion to 3.30V, changes of output voltage and/or input voltage will alter
performance from the data given in the Power Supply Data section.
POWER SUPPLY DATA
The SP6138EB is designed with an accurate 1.5% reference over line, load and
temperature. Figure 1 data shows a typical SP6138ER Evaluation Board efficiency plot,
with efficiencies to 86% and output currents to 3A. SP6138ER Load Regulation in
Figure 2 shows only 0.09% change in output voltage step response from no load to 3A
load. Figures 3 and 4 show the fast transient response of the SP6138. Start-up
response in Figures 5, 6 and 7 show a controlled start-up with different output load
behavior when power is applied where the input current rises smoothly as the soft-start
ramp increases. In Figure 8 the hiccup mode gets activated in response to an output
dead short circuit condition and will soft-start until the over-load is removed. Figures 9
and 10 show output voltage ripple less than 10mV over the complete load range.
While data on individual power supply boards may vary, the capability of the SP6138ER
of achieving high accuracy over a range of load conditions shown here is quite
impressive and desirable for accurate power supply design.
相關PDF資料 |
PDF描述 |
|---|---|
| SP6138EB | Evaluation Board Manual |
| SP6138ER1 | Evaluation Board Manual |
| SP6139 | Busway FS Plug-In 600A |
| SP6139EU | Wide Input, 1.3MHz Synchronous PWM Controller |
| SP6139EU-L | Wide Input, 1.3MHz Synchronous PWM Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SP6138EB | 功能描述:DC/DC 開關控制器 Synchronous Buck Controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| SP6138ER1 | 制造商:Exar Corporation 功能描述: |
| SP6138ER1/TR | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Synchronous Buck Controller |
| SP6138ER1-L | 制造商:Exar Corporation 功能描述:CONTROLLER SYNCH BUCK SMD QFN-16 |
| SP6138ER1-L/TR | 功能描述:開關變換器、穩壓器與控制器 Synchronous Controller RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。