- 您現在的位置：買賣IC網 > PDF目錄372187 > SP6139EU-L Wide Input, 1.3MHz Synchronous PWM Controller PDF資料下載
參數資料
| 型號： | SP6139EU-L |
| 英文描述： | Wide Input, 1.3MHz Synchronous PWM Controller |
| 中文描述： | 寬輸入，1.3MHz同步PWM控制器 |
| 文件頁數： | 5/13頁 |
| 文件大?。?/td> | 148K |
| 代理商： | SP6139EU-L |
5
Date: 12/20/04 SP6139 Wide Input, 1.3MHz Synchronous PWM Controller Copyright 2004 Sipex Corporation
tection features include thermal shutdown and
short-circuit detection. In the event that either a
thermal, short-circuit, or UVLO fault is de-
tected, the SP6139 is forced into an idle state
where the output drivers are held off for a finite
period before a re-start is attempted.
Under Voltage Lock Out (UVLO)
The SP6139 contains two separate UVLO com-
parators to monitor the bias (V
CC
) and conver-
sion (V
IN
) voltages independently. The V
CC
UVLO threshold is internally set to 4.25V,
whereas the V
IN
UVLO threshold is program-
mable through the UVIN pin. When the UVIN
pin is greater than 2.5V, the SP6139 is permitted
to start up pending the removal of all other
faults. Both the V
CC
and V
IN
UVLO compara-
tors have been designed with hysteresis to pre-
vent noise from resetting a fault.
Soft Start
“Soft Start” is achieved when a power converter
ramps up the output voltage while controlling
the magnitude of the input supply source cur-
rent. In a modern step down converter, ramping
up the positive terminal of the error amplifier
controls soft start. As a result, excess source
current can be defined as the current required to
charge the output capacitor.
IV
IN
= C
OUT
* DV
OUT
/ DTSoft-start
The SP6139 provides the user with the option to
program the soft start rate by tying a capacitor
from the SS pin to GND. The selection of this
capacitor is based on the 10uA pull up current
present at the SS pin and the 0.8V reference
voltage. Therefore, the excess source can be
redefined as:
IV
IN
= C
OUT
* DV
OUT
*10
μ
A / (C
SS
* 0.8V)
Hiccup
Upon the detection of a power, thermal, or short-
circuit fault, the SP6139 is forced into an idle
state for 100mS (typical). The SS and COMP
pins are immediately pulled low, and the gate
drivers are held off for the duration of the
timeout period. Power and thermal faults have
to be removed before a restart may be attempted,
whereas, a short-circuit fault is internally cleared
shortly after the fault latch is set. Therefore, a
restart attempt is guaranteed every 100mS (typi-
cal) as long as the short-circuit condition per-
sists.
Thermal and Short-Circuit
Protection
Because the SP6139 is designed to drive large
NFETs running at high current, there is a chance
that either the controller or power converter will
become too hot. Therefore, an internal thermal
shutdown (145
°
C) has been included to prevent
the IC from malfunctioning at extreme tempera-
tures.
A short-circuit detection comparator has also
been included in the SP6139 to protect against
the accidental short or sever build up of current
at the output of the power converter. This com-
parator constantly monitors the positive and
negative terminals of the error amplifier, and if
the V
FB
pin ever falls more than 250mV (typi-
cal) below the positive reference, a short-circuit
fault is set. Because the SS pin overrides the
internal 0.8V reference during soft start, the
SP6139 is capable of detecting short-circuit
faults throughout the duration of soft start as
well as in regular operation.
Error Amplifier and Voltage Loop
As stated before, the heart of the SP6139 voltage
error loop is a high performance, wide band-
width transconductance amplifier. Because of
the amplifier’s current limited (+/-150
μ
A)
transconductance, there are many ways to com-
pensate the voltage loop or to control the COMP
pin externally. If a simple, single pole, single
THEORY OF OPERATION
相關PDF資料 |
PDF描述 |
|---|---|
| SP619 | High Current Power Switch |
| SP619EK-L | High Current Power Switch |
| SP6200EM5-1.5 | Micropower, 100mA and 200mA CMOS LDO Regulators |
| SP6200EM5-1.8 | Micropower, 100mA and 200mA CMOS LDO Regulators |
| SP6200EM5-2.5 | Micropower, 100mA and 200mA CMOS LDO Regulators |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SP6139EU-L/TR | 功能描述:開關變換器、穩壓器與控制器 Wide Input, 1.3MHz Synchronous RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| SP615 | 制造商:Power-One 功能描述: 制造商:Power-One 功能描述:POWER SUPPLY |
| SP6153ER1-L | 制造商:Exar Corporation 功能描述: |
| SP615BABT | 制造商:Power-One 功能描述: |
| SP618 | 制造商:Power-One 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。