參數資料
型號: SP6645UEB
英文描述: Evaluation Board Manual
中文描述: 評估板手冊
文件頁數: 2/5頁
文件大?。?/td> 145K
代理商: SP6645UEB
USING THE EVALUATION BOARD
1) Powering Up the SP6644/6645 Circuit
The SP6644/6645 Evaluation Board
can be powered from inputs from a +0.8V to +3.3V from 1
or 2 alkaline cells or a power supply. Connect with short leads directly to the “Vbatt” and “Gnd”
posts. Monitor the Output Voltage and connect the Load between the “Vout” post and the 2
nd
“GND” post.
2) Using the J1 Jumper: Enabling the SP6644/6645 Output and using the Shutdown Mode
The SP6644/6645 output will be Enabled if the J1 Jumper is in the left or pin 1 to 2 position. If
J1 is in the pin 2 to 3 position, the Shutdown pin is brought to GND, which puts the
SP6644/6645 in the low quiescent Shutdown Mode.
3) Using the LDO Output
The SP6644/6645 output connects to an LDO, the SP6201 ultra low drop-out CMOS regulator
which has a 3.0V output at up to 150mA. To evaluate the SP6201 performance with the
SP6644/6645 input, connect the load across the +3V post and GND and measure both the
SP6644/6645 output and SP6201 output with an oscilloscope configured for AC millivolts. As
you can see from figure 8 the output ripple voltage is reduced from 60mV to less than 3mV by
the LDO.
4) Using the Rlim Function
The peak inductor current,
I
PEAK
, is programmed externally by the
RLIM resistor connected
between the RLIM pin and GND. The peak inductor current is defined by:
I
PEAK
= 1400/R
LIM
The SP6644/45 datasheet specifications for RLIM give a range of 2.5 to 9.3K ohms. Using the
IPEAK equation above gives an IPEAK range of
I
PEAK
range = 150 to 560mA.
The saturation current specified for the inductor needs to be greater then the peak current to
avoid saturating the inductor, which would result in a loss in efficiency and could damage the
inductor. The SP6644/6645 evaluation board uses a Rlim value of 2.5K to allow the circuit to
deliver up to 80mA for 1.3V input and 150mA for 2.6V input. Other values could be selected
using the above relationships.
POWER SUPPLY DATA
The SP6644/6645’s high efficiency is illustrated in figures 1 & 2 which has 90 to 93% efficiency
for 2 fully charged alkaline cells. Figure 1 with Rlim of 2.5K can deliver more output current than
figure 2 with an Rlim of 5K because it has greater peak current, at a price of reduced efficiency.
Line/Load curves in figures 3 & 4 show only 10 to 15mV change in output voltage at rated loads
of 80mA for 1-cell and 150mA for 2-cell. The no-load battery current the SP6644/6645
application circuit consumes for different Rlim’s of 2.5K & 5K is illustrated in figure 5. In figure 6
the maximum load current the SP6644/6645 can deliver for different Rlim’s of 2.5K & 5K is
illustrated. Load transient response to a 15mA to 150mA output load step is shown in figure 7.
Finally, in figure 8, SP6644 output ripple of 60mV is improved with the addition of the SP6201
LDO achieving an output ripple of only 3mV.
2
相關PDF資料
PDF描述
SP6644EB Evaluation Board Manual
SP6644EU Single/Dual Alkaline Cell, High Efficiency Step-Up DC-DC Converter
SP6645 Single/Dual Alkaline Cell, High Efficiency Boost DC-DC Regulator
SP6645EU Single/Dual Alkaline Cell, High Efficiency Step-Up DC-DC Converter
SP6644UEB Evaluation Board Manual
相關代理商/技術參數
參數描述
SP6648 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Ultra-low Quiescent Current, High Efficiency Boost Regulator
SP6648_06 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Ultra-low Quiescent Current, High Efficiency Boost Regulator
SP6648EB 功能描述:DC/DC 開關控制器 Eval Board for SP6648 Series RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
SP6648ER 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Ultra-low Quiescent Current, High Efficiency Boost Regulator
SP6648ER/TR 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Ultra-low Quiescent Current, High Efficiency Boost Regulator