- 您現在的位置：買賣IC網 > PDF目錄372190 > SP6648UEB .15UF 100V 10% MONOLITH CERM CAP PDF資料下載
參數資料
| 型號： | SP6648UEB |
| 英文描述： | .15UF 100V 10% MONOLITH CERM CAP |
| 中文描述： | 評估板手冊 |
| 文件頁數： | 2/5頁 |
| 文件大?。?/td> | 98K |
| 代理商： | SP6648UEB |
USING THE EVALUATION BOARD
1) Powering Up the SP6648LED Circuit
The SP6648LED Evaluation Board
can be powered from inputs from a +1.8V to +3.2V power
supply or from 2 alkaline cells. Connect with short leads directly to the “VIN” and “GND” posts.
Plug the 1W LumiLED between the “VOUT” and “REF” posts. Unlike other boost regulators, the
part has self-protection feature. It will not be damaged when the output is open as long as there
is a low resistance from FB to GND. As shown in Figures 1 and 2, if the board is powered up
before the LumiLED is plugged in, the circuit will bring the Feedback pin to 0V and the SP6648
has a feature to set the output voltage to be 3.3V. Once the LumiLED is plugged in, the
Feedback pin will go up to 1.25V and begin to regulate. The output voltage will go from 3.3V to
3.68V (=V
F
+0.61V) accordingly (as shown in Fig. 1), where V
F
is the forward voltage of the
LumiLED. When the LumiLED is open, the Feedback pin voltage will go to 0V and the output
voltage will go to 3.3V which will protect the part (as shown in Fig 2).
Fig 1. Plug in the LumiLED
Fig. 2. Unplug the LumiLED
2) Using the J1 Jumper: Enabling the SP6648 Output and using the Shutdown Mode
The SP6648 output will be enabled if the J1 Jumper is in the top or pin 1 to 2 position. If J1 is in
the pin 2 to 3 position, the Shutdown pin is brought to GND, which puts the SP6648 in the low
quiescent Shutdown Mode.
3) Selecting the Bias Resistor
In the white LEDs application, the SP6648 is generally programmed as a current source. The
bias resistor is used to set the operating current of the white LED as equation
V
R
=
F
REF
I
b
where V
REF
is around 0.61V, I
F
is the operating current of the Lumiled. To set the operating
current to be about 350mA, R
b
is selected as 1.8 Ohm as shown in the schematic.
4) Vout Programming
The SP6648 can be programmed as either a voltage source or a current source. To program the
SP6648 as voltage source, the SP6648 requires 2 feedback resistors R
6
& R
7
to control the
output voltage. To set Vout in the voltage mode, use the equation:
V
R
7
out
61
6
R
1
.
=
V
OUT
V
OUT
V
REF
V
REF
相關PDF資料 |
PDF描述 |
|---|---|
| SP6650UEB | 320 x 240 pixel format, Chip-On-Glass Technology |
| SP6650 | High Efficiency 600mA Synchronous Buck Regulator Ideal for portable designs powered with Li Ion battery |
| SP6650EB | Evaluation Board Manual |
| SP6650EU | High Efficiency 600mA Synchronous Buck Regulator Ideal for portable designs powered with Li Ion battery |
| SP6656ER | High Efficiency 400mA Synchronous Buck Regulator with Bit Programmable Output |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SP6649 | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Ultra-low Quiescent Current, High Efficiency Boost DC-DC Regulator |
| SP6649EU | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Ultra-low Quiescent Current, High Efficiency Boost DC-DC Regulator |
| SP6649EU/TR | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Ultra-low Quiescent Current, High Efficiency Boost DC-DC Regulator |
| SP664P7FC9086 | 制造商:Thomas & Betts 功能描述:Flush Service Floor Boxes |
| SP6650 | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:High Efficiency 600mA Synchronous Buck Regulator Ideal for portable designs powered with Li Ion battery |
發布緊急采購，3分鐘左右您將得到回復。