- 您現在的位置：買賣IC網 > PDF目錄372191 > SP6690EK1 CAP CERM .5PF 25V NP0 0201 PDF資料下載
參數資料
| 型號： | SP6690EK1 |
| 英文描述： | CAP CERM .5PF 25V NP0 0201 |
| 中文描述： | 微功率升壓穩壓器系列白光LED驅動器 |
| 文件頁數： | 10/16頁 |
| 文件大?。?/td> | 270K |
| 代理商： | SP6690EK1 |
10
Date: 05/25/04
SP6690 Micro Power Boost Regualtor, Series White LED Driver Copyright 2004 Sipex Corporation
precision resistors are recommended. Table 3
below shows the R
b
selection for different white
LED currents. For example, to set the operating
current to be 20mA, R
b
is selected as 60.4
, as
shown in the schematic.
Table 3. Bias Resistor Selection
I
F
(mA)
5
10
12
15
20
R
b
(
)
243
121
102
80.6
60.4
Output Voltage Program
The SP6690 can be programmed as either a
voltage source or a current source. To program
the SP6690 as voltage source, the SP6690 re-
quires 2 feedback resistors R
1
& R
2
to control
the output voltage. As shown in Figure 22.
Table 4. Divider Resistor Selection
V
OUT
(V)
12
15
18
21
30
R
1
(
)
1M
1M
1M
1M
1M
R
2
(
)
113K
88.7K
73.2K
61.9K
42.2K
Brightness Control
Dimming control can be achieved by applying a
PWM control signal to the SHDN pin. The
brightness of the white LEDs is controlled by
increasing and decreasing the duty cycle of The
PWM signal. A 0% duty cycle corresponds to
zero LED current and a 100% duty cycle corre-
sponds to full load current. While the operating
frequency range of the PWM control is from
60Hz to 700Hz, the recommended maximum
brightness frequency range of the PWM signal
is from 60Hz to 200Hz. A repetition rate of at
least 60Hz is required to prevent flicker. The
magnitude of the PWM signal should be higher
than the minimum SHDN voltage high.
Open Circuit Protection
When any white LED inside the white LED
module fails or the LED module is disconnected
from the circuit, the output and the feedback
control will be open, thus resulting in a high
output voltage, which may cause the SW pin
voltage to exceed it maximum rating. In this
case, a zener diode can be used at the output to
limit the voltage on the SW pin and protect the
part. The zener voltage should be larger than the
maximum forward voltage of the White LED
module.
APPLICATION INFORMAMTION: Continued
L1
1.22V
R2
D1
C1
C2
R1
VOUT
U1
SP6690
1
2
3
4
5
SW
GND
FB
SHDN
V
IN
VIN
Figure 22. Using SP6690 as Voltage Source
The formula and table for the resistor selection
are shown below:
R
=
(
V
OUT
- 1
)
R
2
1.22
相關PDF資料 |
PDF描述 |
|---|---|
| SP6691 | Micro Power Boost Regulator Series White LED Driver |
| SP674AA | 12-Bit Sampling A/D Converters |
| SP674AB | 12-Bit Sampling A/D Converters |
| SP674AC | 12-Bit Sampling A/D Converters |
| SP674AJ | 12-Bit Sampling A/D Converters |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SP6690EK1/TR | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Micro Power Boost Regulator Series White LED Driver |
| SP6690EK-L | 制造商:Exar Corporation 功能描述:BOOST REG WHITE LED DRIVE 6690 |
| SP6690EK-L/TR | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| SP6690ER | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Micro Power Boost Regulator Series White LED Driver |
| SP6690ER/TR | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Micro Power Boost Regulator Series White LED Driver |
發布緊急采購，3分鐘左右您將得到回復。