參數資料
型號: SP674BT
元件分類: 串行ADC
英文描述: 12-Bit Sampling A/D Converters
中文描述: 12位采樣的A / D轉換器
文件頁數: 10/14頁
文件大小: 204K
代理商: SP674BT
12
Conversion Length
A conversion start transition latches the state of
A
as shown in
Figure 8
and
Table 1
. The latched
state determines if the conversion stops with 8–
bits (A
high) or continues for 12–bits (A
low).
If all 12–bits are read following an 8–bit conver-
sion, the three LSB’s will be a logic “0” and DB
3
will be a logic “1”. A
is latched because it is also
involved in enabling the output buffers as ex-
plained elsewhere. No other control inputs are
latched.
Stand–Alone Operation
The simplest interface is a control line connected
to R/C. The other controls must be tied to known
states as follows: CE and 12/8 are wired high, A
0
and CS are wired low. The output data arrives in
words of 12–bits each. The limits on R/C duty
cycle are shown in
Figures 9
and
10
. The duty
cycle may be within and including the extremes
shown in the specifications. In general, data may
be read when R/C is high unless STS is also high,
indicating a conversion is in progress.
Reading Output Data
The output data buffers remain in a high imped-
ance state until the following four conditions are
met: R/C is high, STS is low, CE is high and CS
is low. The data lines become active in response
to these four conditions, and output data accord-
ing to the conditions of the control lines 12/8 and
A
0
. The timing diagram for this process is shown
in
Figure 11
. When 12/8 is high, all 12 data
outputs become active simultaneously and the
A
input is ignored. The 12/8 input is usually tied
high or low; it is TTL/CMOS compatible. When
12/8 is low, the output is separated into two 8–bit
bytes as shown below:
BYTE 1
xxxx xxxx
BYTE2
xxxx 0000
MSB
LSB
This configuration makes it easy to connect to an
8–bit address bus as shown in
Figure 7
. The A
0
control can be connected to the least significant
bit of the data bus in order to store the output data
into two consecutive memory locations. When
A
is pulled low, the 8 MSB’s are enabled only.
When A
0
is high, the 8 MSB’s are disabled, bits
4 through 7 are forced to a zero and the four
LSB’s are enabled. The two byte format is “l(fā)eft
justified data” as shown above and can be con-
sidered to have a decimal point or binary to the
left of byte 1.
A
may be toggled without damage to the con-
verter at any time. Break–before–make action is
guaranteed between the two data bytes. This
assures that the outputs which are strapped to-
gether in
Figure 11
will never be enabled at the
same time.
In
Figure 11
, it can be seen that a read operation
usually begins after the conversion is complete
and STS is low. If earlier access is needed, the
read can begin no later than the addition of times
t
DD
and t
HS
before STS goes low.
Figure 7. Interfacing SPx74A to 8–Bit Interface Bus
28
27
26
25
24
23
22
21
20
19
18
17
16
15
STS
DB11 (MSB)
DB0 (LSB)
DIG
COM
SPx74A
2
4
A0
ADDRESS BUS
A0
12/8
BUS
相關PDF資料
PDF描述
SP6828-5EK +3V Low Power Voltage Inverters
SP6828EK +3V Low Power Voltage Inverters
SP6828TR +3V Low Power Voltage Inverters
SP6828 3V Low Power Charge Pump Voltage Inverters(3V,12kHz,低功耗電荷泵電壓反相器)
SP6829 3V Low Power Charge Pump Voltage Inverters(3V,35kHz,低功耗電荷泵電壓反相器)
相關代理商/技術參數
參數描述
SP67596 制造商:L COM 功能描述:CA DB50F DB50M CST WIR 2.5F 制造商:L-com Inc 功能描述:CA DB50F DB50M CST WIR 2.5F
SP-67-B 制造商:Triad Magnetics 功能描述:SP-67 Series 300 Hz to 100 kHz Triad High Reliability Audio Transformer
SP68 功能描述:變壓器音頻和信號 10K 10K CT/2K SPLIT PRI/SEC RED SPEC RoHS:否 制造商:Skyworks Solutions, Inc. 頻率范圍:810 MHz to 960 MHz 初級線圈阻抗: 次級線圈阻抗: 絕緣電壓:23 dB 工作溫度范圍:- 40 C to + 85 C 端接類型:SMD/SMT 尺寸:6 mm L x 4.9 mm W x 1.6 mm H 產品:Splitters and Combiners
SP-68 功能描述:TRANS 10K/10KCT 2.5K SPLIT AUDIO RoHS:是 類別:變壓器 >> 音頻 系列:- 標準包裝:1 系列:TTC 變壓器類型:數據/音頻耦合 電流:- 阻抗:600 主,490CT 副 插入損耗:1.5dB 安裝類型:表面貼裝 尺寸/尺寸:13.50mm L x 14.00mm W 高度 - 座高(最大):10.40mm 端接類型:鷗翼型 其它名稱:MT7210CT
SP6801 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Universal High Brightness LED Driver