- 您現在的位置：買賣IC網 > PDF目錄372191 > SP691ACP Low Power Microprocessor Supervisory with Battery Switch-Over PDF資料下載
參數資料
| 型號： | SP691ACP |
| 英文描述： | Low Power Microprocessor Supervisory with Battery Switch-Over |
| 中文描述： | 低功耗微處理器監控與電池開關過 |
| 文件頁數： | 3/7頁 |
| 文件大?。?/td> | 54K |
| 代理商： | SP691ACP |
SP691AEB/03
SP691A/693A Evaluation Board Manual
3
Copyright 2000 Sipex Corporation
Pin 7 – OSC IN – External Oscillator Input.
When OSC SEL is unconnected or driven high,
a 10
μ
A pull-up connects from V
to OSC IN,
the internal oscillator sets the reset and watchdog
timeout periods, and OSC IN selects between
fast and slow watchdog timeout periods. When
OSC SEL is driven low, the reset and watchdog
timeout periods may be set either by a capacitor
from OSC IN to ground or by an external clock
at OSC IN.
Pin 8 – OSC SEL – Oscillator Select. When OSC
SEL is unconnected or driven high, the internal
oscillator sets the reset and watchdog timeout
periods. When OSC SEL is low, the external
oscillator input (OSC IN) is enabled. OSC SEL
has a 10
μ
A pull-up.
Pin 9 – PFI – Power-Fail Input. This is the
non-inverting input to the power-fail comparator.
When PFI is less than 1.25V, PFO_N goes low.
Connect PFI to GND or VOUT when not used.
Connect external divider R1 & R2 to Probe Pins
and connect Unregulated Voltage to UNREG
for Power Fail monitoring.
Pin 10 – PFO – Power-Fail Output. This is the
output of the power-fail comparator. PFO, goes
low when PFI is less than 1.25V. This is an
uncommitted comparator, and has no effect on
any other internal circuitry.
Pin 11 – WDI – Watchdog Input. WDI is a
three-level input. If WDI remains either high or
low for longer than the watchdog timeout
period, WDO goes low and reset is asserted for
the reset timeout period. WDO remains low
until the next transition at WDI. Leaving WDI
unconnected disables the watchdog function.
WDI connects to an internal voltage divider
between V
and GND, which sets it to
mid-supply when left unconnected. For a simple
check of watchdog function, connect WDI to
either Probe pins GND or V
OUT
to cause WDO
to go to a Logic Low.
Pin 12 – CE OUT – Chip-Enable Output. The
Chip-Enable (CE) function CE OUT provides
internal gating of chip enable signals to prevent
erroneous data from corrupting the CMOS RAM
in the event of a power failure. During normal
operation, the CE gate is enabled and all CE
transitions are passed from CE IN to CE OUT.
When Reset is asserted, this path is disabled.
Note that CE OUT goes low (active) only when
CE IN is low and V
is above the reset threshold.
If CE IN is low when reset is asserted, CE OUT
will stay low for 12
μ
s or until CE IN goes high,
whichever occurs first.
Pin 13 – CE IN – Chip-Enable Input. The Input
to chip-enable gating circuit. Connect to GND
or V
OUT
if not used.
Pin 14 –WDO – Watchdog Output. WDO goes
low and reset is asserted if WDI remains either
high or low longer than the watchdog timeout
period. WDO returns high on the next transition
at WDI. WDO remains high if WDI is
unconnected. WDO is also high when RESET
is asserted.
Pin 15 – RESET – RESET output goes low
whenever V
falls below the reset threshold.
RESET will remain low for 200ms (when
internal oscillator is used) after V
CC
crosses the
reset threshold on power-up.
Pin 16 – RESET – RESET Output goes high
whenever V
falls below the reset threshold.
RESET is open drain and is the inverse of
RESET.
Note: To accurately measure the extremely small
supply current in Battery Back-up mode, you
need to cut split pads SP1 & SP2 (solder side
of board) severing connections to C1 & C2
which would have leakage currents in the
measurement range. Also, remove charging
circuit components CBATT and D1 if they are
installed.
相關PDF資料 |
PDF描述 |
|---|---|
| SP691ACT | Low Power Microprocessor Supervisory with Battery Switch-Over |
| SP691AEN | Low Power Microprocessor Supervisory with Battery Switch-Over |
| SP691AEP | Low Power Microprocessor Supervisory with Battery Switch-Over |
| SP691AET | Low Power Microprocessor Supervisory with Battery Switch-Over |
| SP693A | Low Power Microprocessor Supervisory with Battery Switch-Over(低功耗，微處理器監控電路（帶電池開關）) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SP691ACP-L | 功能描述:監控電路 LW PWR MICRO 5.5V 25mA-250mA BAT SW/OV RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| SP691ACT | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
| SP691ACT/TR | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Low Power Microprocessor Supervisory with Battery Switch-Over |
| SP691ACT-L | 功能描述:監控電路 LW PWR MICRO 5.5V 25mA-250mA BAT SW/OV RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| SP691ACT-L/TR | 功能描述:監控電路 LW PWR MICRO 5.5V 25mA-250mA BAT SW/OV RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。