- 您現在的位置：買賣IC網 > PDF目錄372194 > SP7800AKS 12-Bit 3ms Sampling A/D Converter PDF資料下載
參數資料
| 型號： | SP7800AKS |
| 英文描述： | 12-Bit 3ms Sampling A/D Converter |
| 中文描述： | 12位為3ms采樣A / D轉換器 |
| 文件頁數： | 8/13頁 |
| 文件大?。?/td> | 171K |
| 代理商： | SP7800AKS |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁
SP7800ADS/02
SP7800A 12-Bit 3
μ
s Sampling A/D Converter
8
Copyright 2000 Sipex Corporation
maximum system accuracy, both should be well–
isolated from digital supplies with wide load varia-
tions.
To limit the effects of digital switching elsewhere in a
system on the analog performance of the system, it
often makes sense to run a separate +5V supply
conductor from the supply regulator to any analog
components requiring +5V, including the
SP7800A.
If the
SP7800A
traces cannot be separated back to the
power supply terminals, and therefore share the same
trace as the logic supply currents, then a 10 Ohm
isolating resistor should be used between the board
supply and pin 24 (V
) and its bypass capacitors to
keep V
glitch–free. The V
pins (23 and 24) should
be connected together and bypassed with a parallel
combination of a 6.8
μ
F Tantalum capacitor and a
0.1
μ
F ceramic capacitor located close to the converter
to obtain noise-free operation. (See
Figure 1
). Noise
on the power supply lines can degrade converter
performance, especially noise and spikes from a
switching power supply. Appropriate supplies or
filters must be used.
The GND pins (4 and 13) are also separated internally,
and should be directly connected to a ground plane
under the converter. A ground plane is usually the best
solution for preserving dynamic performance and
reducing noise coupling into sensitive converter cir-
cuits. Where any compromises must be made, the
common return of the analog input signal should be
referenced to pin 4, AGND, on the
SP7800A,
which
prevents any voltage drops that might occur in the
power supply common returns from appearing in
series with the input signal.
Coupling between analog input and digital lines should
be minimized by careful layout. For instance, if the
lines must cross, they should do so at right angles.
Parallel analog and digital lines should be separated
from each other by a pattern connected to common.
If external full scale and offset potentiometers are
used, the potentiometers and related resistors should
be located as close to the
SP7800A
as possible.
“Hot Socket” Precaution
Two separate +5V V
pins, 23 and 24, are used to
minimize noise caused by digital transients. If one pin
is powered and the other is not, the
SP7800A
may
draw excessive current. In normal operation, this is not
a problem because both pins will be soldered together.
However, during evaluation, incoming inspection,
repair, etc., where the potential of a “Hot Socket”
exists, care should be taken to apply power to the
SP7800A
only after it has been socketed.
Minimizing “Glitches”
Coupling of external transients into an analog-to-
digital converter can cause errors which are difficult to
debug. In addition to the discussions earlier on layout
considerations for supplies, bypassing and grounding,
there are several other useful steps that can be taken to
get the best analog performance out of a system using
Figure 4. Acquisition and Conversion Timing
R/C
BUSY
Converter
Mode
Acquisition
Conversion
Acquisition
Conversion
t
AP
Hold Time
t
C
t
DBC
t
B
SYMBOL/PARAMETER
t
DBC
BUSY delay from R/C
t
B
BUSY Low
t
AP
Aperture Delay
t
AP
Aperture Jitter
t
C
Conversion Time
MIN
TYP
80
2.5
13
150
2.47
MAX
150
2.7
UNITS
ns
μ
s
ns
ps, rms
2.70
μ
s
相關PDF資料 |
PDF描述 |
|---|---|
| SP782 | Programmable Charge Pump |
| SP782CP | Programmable Charge Pump |
| SP782CT | Programmable Charge Pump |
| SP784 | Programmable Charge Pump |
| SP784CP | Programmable Charge Pump |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SP7805AIS WAF | 制造商:Texas Instruments 功能描述: |
| SP7805V2-L | 功能描述:DC/DC 開關控制器 30 TERMINAL 1A POS RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| SP7805V2-L/TR | 功能描述:DC/DC 開關控制器 30 TERMINAL 1A POS RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| SP7805V2-L-TR | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:3-Terminal Positive Regulators |
| SP7805V-L | 功能描述:DC/DC 開關控制器 30 TERMINAL 1A POS RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
發布緊急采購，3分鐘左右您將得到回復。