參數資料
型號: SPC5604PEF0MLQ6
廠商: Freescale Semiconductor
文件頁數: 10/104頁
文件大?。?/td> 0K
描述: IC MCU 32BIT 512KB FLASH 144LQFP
標準包裝: 60
系列: MPC56xx Qorivva
核心處理器: e200z0h
芯體尺寸: 32-位
速度: 64MHz
連通性: CAN,F(xiàn)lexRay,LIN,SPI,UART/USART
外圍設備: DMA,POR,PWM,WDT
輸入/輸出數: 108
程序存儲器容量: 512KB(512K x 8)
程序存儲器類型: 閃存
EEPROM 大?。?/td> 64K x 8
RAM 容量: 40K x 8
電壓 - 電源 (Vcc/Vdd): 3 V ~ 5.5 V
數據轉換器: A/D 30x10b
振蕩器型: 內部
工作溫度: -40°C ~ 125°C
封裝/外殼: 144-LQFP
包裝: 托盤
MPC5604P Microcontroller Data Sheet, Rev. 8
Freescale
13
1.5.17.1
Boot assist module (BAM)
The BAM is a block of read-only one-time programmed memory and is identical for all MPC560xP devices that are based on
the e200z0h core. The BAM program is executed every time the device is powered on if the alternate boot mode has been
selected by the user.
The BAM provides the following features:
Serial bootloading via FlexCAN or LINFlex
Ability to accept a password via the used serial communication channel to grant the legitimate user access to the
non-volatile memory
1.5.18
Error correction status module (ECSM)
The ECSM provides a myriad of miscellaneous control functions regarding program-visible information about the platform
configuration and revision levels, a reset status register, a software watchdog timer, wakeup control for exiting sleep modes,
and information on platform memory errors reported by error-correcting codes and/or generic access error information for
certain processor cores.
The Error Correction Status Module supports a number of miscellaneous control functions for the platform. The ECSM includes
these features:
Registers for capturing information on platform memory errors if error-correcting codes (ECC) are implemented
For test purposes, optional registers to specify the generation of double-bit memory errors are enabled on the
MPC5604P.
The sources of the ECC errors are:
Flash memory
SRAM
1.5.19
Peripheral bridge (PBRIDGE)
The PBRIDGE implements the following features:
Duplicated periphery
Master access privilege level per peripheral (per master: read access enable; write access enable)
Write buffering for peripherals
Checker applied on PBRIDGE output toward periphery
Byte endianess swap capability
1.5.20
Controller area network (FlexCAN)
The MPC5604P MCU contains one controller area network (FlexCAN) module. This module is a communication controller
implementing the CAN protocol according to Bosch Specification version 2.0B. The CAN protocol was designed to be used
primarily as a vehicle serial data bus, meeting the specific requirements of this field: real-time processing, reliable operation in
the EMI environment of a vehicle, cost-effectiveness and required bandwidth. The FlexCAN module contains 32 message
buffers.
The FlexCAN module provides the following features:
Full implementation of the CAN protocol specification, version 2.0B
— Standard data and remote frames
— Extended data and remote frames
— Up to 8-bytes data length
— Programmable bit rate up to 1 Mbit/s
相關PDF資料
PDF描述
EGG.1B.308.CYM CONN RCPT 8POS PNL MNT SKT W/NUT
MC68HC16Z1CEH16 IC MCU 16BIT 16MHZ 132-PQFP
VE-B6J-IW-B1 CONVERTER MOD DC/DC 36V 100W
VE-B6H-IX-B1 CONVERTER MOD DC/DC 52V 75W
VE-B6D-IW-B1 CONVERTER MOD DC/DC 85V 100W
相關代理商/技術參數
參數描述
SPC5604PEF0MLQ7R 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:microcontroller units (MCUs)
SPC5604PEF0VLL7R 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:microcontroller units (MCUs)
SPC5604PEF0VLQ7R 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:microcontroller units (MCUs)
SPC5604PEF1MLL6 功能描述:32位微控制器 - MCU RoHS:否 制造商:Texas Instruments 核心:C28x 處理器系列:TMS320F28x 數據總線寬度:32 bit 最大時鐘頻率:90 MHz 程序存儲器大小:64 KB 數據 RAM 大小:26 KB 片上 ADC:Yes 工作電源電壓:2.97 V to 3.63 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:LQFP-80 安裝風格:SMD/SMT
SPC5604PEF1MLQ6 功能描述:32位微控制器 - MCU 512K FLASH, 40K RAM, RoHS:否 制造商:Texas Instruments 核心:C28x 處理器系列:TMS320F28x 數據總線寬度:32 bit 最大時鐘頻率:90 MHz 程序存儲器大小:64 KB 數據 RAM 大小:26 KB 片上 ADC:Yes 工作電源電壓:2.97 V to 3.63 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:LQFP-80 安裝風格:SMD/SMT