- 您現在的位置：買賣IC網 > PDF目錄372101 > SR201C223KTA KONDENSATOR RADIAL 0.022UF 100V 5ST PDF資料下載
參數資料
| 型號： | SR201C223KTA |
| 英文描述： | KONDENSATOR RADIAL 0.022UF 100V 5ST |
| 中文描述： | KONDENSATOR徑向0.022UF 100V的5ST |
| 文件頁數： | 10/72頁 |
| 文件大?。?/td> | 1107K |
| 代理商： | SR201C223KTA |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
8
The Capacitor
GENERAL ELECTRICAL AND
ENVIRONMENTAL SPECIFICATIONS
Many AVX ceramic capacitors are purchased in accordance
with Military Specifications, MIL-C-39014, MIL-C-11015,
MIL-C-20, MIL-C-55681, and MIL-C-123 or according to
individual customer specification. When ordered to these
specifications, the parts will meet the requirements set forth
in these documents. The General Electrical and
Environmental Specifications listed below detail test
conditions which are common to the foregoing and to most
ceramic capacitor specifications. If additional information is
needed, AVX Application Engineers are ready to assist you.
Capacitance –
Capacitance shall be tested in accordance
with Method 305 of MIL-STD-202.
Class 1
dielectric to 1000 pF measured at 1 MHz, ± 100
KHz, > 1000 pF measured at 1 KHz ± 100 Hz both at 1.0
± 0.2 VAC.
Class 2
dielectrics (except High K) to 100 pF shall be mea-
sured at 1 MHz ± 100 KHz, > 100 pF measured at 1 KHz ±
100 Hz both at 1.0 ± 0.2 VAC.
High K
dielectrics measured at 1 KHz ± 100 Hz with less
than 0.5 VAC or less applied.
Dissipation Factor –
D.F. shall be measured at the same
frequency and voltage as specified for capacitance.
Dielectric Strength –
The dielectric strength shall be mea-
sured in accordance with Method 301 of MIL-STD-202 with
a suitable resistor in series with the power supply to limit
the charging current to 50 ma. max.
Insulation Resistance –
Insulation Resistance shall be
measured in accordance with Method 302 of MIL-STD-202
with rated voltage or 200 VDC whichever is less applied.
The current shall be limited to 50 ma. max. and the charg-
ing time shall be 2.0 minutes maximum.
Burn-In –
(Where specified.) 100% of the parts shall be
subjected to 5 cycles of Thermal Shock per Method 107
Test Condition A of MIL-STD-202 followed by voltage con-
ditioning at twice rated voltage and maximum rated tem-
perature for 100 hours or as specified. After Burn-In, parts
shall meet all initial requirements.
Barometric Pressure –
Capacitors shall be tested in
accordance with Method 105 of MIL-STD-202 Test
Condition D (100,000 ft.) with 100% rated voltage applied
for 5 seconds with current limited to 50 ma. No evidence of
flashover or damage is permitted.
Solderability –
Capacitors shall be tested in accordance
with Method 208 of MIL-STD-202 with 95% coverage of
new solder.
Vibration –
Capacitors shall be tested in accordance with
Method 208 Test Condition D of MIL-STD-202 with the
bodies rigidly clamped. The specimens shall be tested in 3
mutually perpendicular planes for a total of 8 hours with
125% rated DC voltage applied. No evidence of opens,
intermittents or shorts is permitted.
Shock –
Capacitors shall be tested in accordance with
Method 213 Condition 1 (100 Gs) of MIL-STD-202 with the
bodies rigidly clamped. No evidence of opens, intermit-
tents or shorts is permitted.
Thermal Shock and Immersion –
Capacitors shall be
tested in accordance with Method 107 Condition A of
MIL-STD-202 with high test temperature (maximum rated
operating temperature) followed by Method 104 of
MIL-STD-202 Test Condition B.
Moisture Resistance –
Capacitors shall be tested in
accordance with Method 106 of MIL-STD-202 with rated
voltage or 100 VDC whichever is less applied for the first 10
cycles.
Resistance to Solder Heat –
Capacitors shall be tested in
accordance with Method 210 of MIL-STD-202 with immer-
sion to .050 of body. AVX Ceralam capacitors are manu-
factured with solder which melts at a temperature greater
than 450°F.
General Considerations –
The application of voltage or
temperature usually causes temporary changes in the
capacitance of Class 2 ceramic capacitors. These changes
are normally in the positive direction and may cause out-of-
tolerance capacitance readings. If a capacitance reading is
made immediately after a dielectric strength or insulation
resistance test and parts are high capacitance, they should
be re-read after a minimum wait of 12 hours.
相關PDF資料 |
PDF描述 |
|---|---|
| SR201C333KTA | KONDENSATOR RADIAL 0.033UF 100V 5ST |
| SR201C473KTA | KONDENSATOR RADIAL 0.047UF 100V 5ST |
| SR211C473KTA | KONDENSATOR RADIAL 0.047UF 100V 5ST |
| SR211C473MTA | KONDENSATOR RADIAL 0.047UF 100V 5ST |
| SR211C682KT600C | KONDENSATOR RADIAL 0.0068UF 100V 5ST |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SR201C223MAA | 功能描述:多層陶瓷電容器MLCC - 含引線 100volts 0.022uF 20% X7R RoHS:否 制造商:AVX 電容:470 pF 容差:10 % 電壓額定值:3 kV 端接類型:Radial 工作溫度范圍: 溫度系數/代碼:X7R 引線間隔:5.08 mm 產品:Automotive MLCCs 引線類型: |
| SR201C223MAATR1 | 制造商:AVX Corporation 功能描述: |
| SR201C223MAR | 功能描述:多層陶瓷電容器MLCC - 含引線 100volts 22000pF 20% X7R RoHS:否 制造商:AVX 電容:470 pF 容差:10 % 電壓額定值:3 kV 端接類型:Radial 工作溫度范圍: 溫度系數/代碼:X7R 引線間隔:5.08 mm 產品:Automotive MLCCs 引線類型: |
| SR201C223MARTR2 | 功能描述:多層陶瓷電容器MLCC - 含引線 100V 0.022uF 20% Radial RoHS:否 制造商:AVX 電容:470 pF 容差:10 % 電壓額定值:3 kV 端接類型:Radial 工作溫度范圍: 溫度系數/代碼:X7R 引線間隔:5.08 mm 產品:Automotive MLCCs 引線類型: |
| SR201C273JAATR1 | 功能描述:多層陶瓷電容器MLCC - 含引線 100volts 0.027uF 5% X7R RoHS:否 制造商:AVX 電容:470 pF 容差:10 % 電壓額定值:3 kV 端接類型:Radial 工作溫度范圍: 溫度系數/代碼:X7R 引線間隔:5.08 mm 產品:Automotive MLCCs 引線類型: |
發布緊急采購，3分鐘左右您將得到回復。