參數資料
型號: SSM2377ACBZ-R7
廠商: Analog Devices Inc
文件頁數: 5/16頁
文件大?。?/td> 0K
描述: IC AUDIO AMP 2.5W MONO D 9WLCSP
產品變化通告: 8mm Carrier Tape Changes 28/Feb/2012
標準包裝: 1
類型: D 類
輸出類型: 1-通道(單聲道)
在某負載時最大輸出功率 x 通道數量: 3.17W x 1 @ 4 歐姆
電源電壓: 2.5 V ~ 5.5 V
特點: 消除爆音,差分輸入,短路和熱保護,關閉
安裝類型: 表面貼裝
供應商設備封裝: 9-WLCSP(1.24x1.24)
封裝/外殼: 9-UFBGA,WLCSP
包裝: 標準包裝
其它名稱: SSM2377ACBZ-R7DKR
SSM2377
Rev. 0 | Page 13 of 16
THEORY OF OPERATION
OVERVIEW
The SSM2377 mono Class-D audio amplifier features a filterless
modulation scheme that greatly reduces the external component
count, conserving board space and, thus, reducing system cost.
The SSM2377 does not require an output filter but, instead, relies
on the inherent inductance of the speaker coil and the natural
filtering of the speaker and human ear to fully recover the audio
component of the square wave output.
Most Class-D amplifiers use some variation of pulse-width
modulation (PWM), but the SSM2377 uses Σ-Δ modulation to
determine the switching pattern of the output devices, resulting
in a number of important benefits.
Σ-Δ modulators do not produce a sharp peak with many
harmonics in the AM frequency band, as pulse-width
modulators often do.
Σ-Δ modulation provides the benefits of reducing the
amplitude of spectral components at high frequencies,
that is, reducing EMI emissions that might otherwise be
radiated by speakers and long cable traces.
Due to the inherent spread-spectrum nature of Σ-Δ modu-
lation, the need for oscillator synchronization is eliminated
for designs that incorporate multiple SSM2377 amplifiers.
The SSM2377 also integrates overcurrent and overtemperature
protection.
GAIN SELECTION
The preset gain of the SSM2377 can be set to 6 dB or 12 dB
using the GAIN pin, as shown in Table 5.
Table 5. GAIN Pin Function Description
Gain Setting (dB)
GAIN Pin Configuration
6
Tie to VDD
12
Tie to GND
POP-AND-CLICK SUPPRESSION
Voltage transients at the output of audio amplifiers can occur
when shutdown is activated or deactivated. Voltage transients
as low as 10 mV can be heard as an audible pop in the speaker.
Clicks and pops can also be classified as undesirable audible
transients generated by the amplifier system and, therefore, as
not coming from the system input signal.
The SSM2377 has a pop-and-click suppression architecture that
reduces these output transients, resulting in noiseless activation
and deactivation from the SD control pin.
EMI NOISE
The SSM2377 uses a proprietary modulation and spread-spectrum
technology to minimize EMI emissions from the device. For
applications that have difficulty passing FCC Class B emission
tests or experience antenna and RF sensitivity problems, the
ultralow EMI architecture of the SSM2377 significantly reduces
the radiated emissions at the Class-D outputs, particularly above
100 MHz. Figure 35 shows the low radiated emissions from the
SSM2377 due to its ultralow EMI architecture.
60
50
40
30
20
10
0
EL
EC
T
R
IC
F
IE
L
D
ST
R
E
N
G
T
H
(
d
B
V/
m
)
30
130
230
330
430
530
FREQUENCY (MHz)
630
730
830
930
100
0
+
09
82
4-
03
5
FCC CLASS B LIMIT
HORIZONTAL POLARIZATION
VERTICAL POLARIZATION
Figure 35. EMI Emissions from the SSM2377
The measurements for Figure 35 were taken in an FCC-certified
EMI laboratory with a 1 kHz input signal, producing 1.0 W of
output power into an 8 Ω load from a 5.0 V supply. The SSM2377
passed FCC Class B limits with 50 cm, unshielded twisted pair
speaker cable. Note that reducing the power supply voltage greatly
reduces radiated emissions.
OUTPUT MODULATION DESCRIPTION
The SSM2377 uses three-level, Σ-Δ output modulation. Each
output can swing from GND to VDD and vice versa. Ideally, when
no input signal is present, the output differential voltage is 0 V
because there is no need to generate a pulse. In a real-world
situation, noise sources are always present.
Due to the constant presence of noise, a differential pulse is
generated, when required, in response to this stimulus. A small
amount of current flows into the inductive load when the differ-
ential pulse is generated.
Most of the time, however, the output differential voltage is 0 V,
due to the Analog Devices, Inc., three-level, Σ-Δ output modula-
tion. This feature ensures that the current flowing through the
inductive load is small.
相關PDF資料
PDF描述
AD574AJPZ IC ADC 12BIT W/REF/CLK 28-PLCC
VE-2T1-IW-F4 CONVERTER MOD DC/DC 12V 100W
VE-2T1-IW-F3 CONVERTER MOD DC/DC 12V 100W
VE-244-IW-F4 CONVERTER MOD DC/DC 48V 100W
AD9248BCPZ-40 IC ADC 14BIT DUAL 40MSPS 64LFCSP
相關代理商/技術參數
參數描述
SSM2377ACBZ-RL 功能描述:IC AUDIO AMP 2.5W MONO D 9WLCSP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:- 標準包裝:2,000 系列:- 類型:AB 類 輸出類型:2 通道(立體聲) 在某負載時最大輸出功率 x 通道數量:- 電源電壓:4 V ~ 18 V 特點:- 安裝類型:通孔 供應商設備封裝:8-DIP 封裝/外殼:8-DIP(0.300",7.62mm) 包裝:管件
SSM2380CBZ 制造商:Analog Devices 功能描述:IC AMP AUDIO 16WLCSP 制造商:Analog Devices 功能描述:IC, AMP, AUDIO, 16WLCSP
SSM2380CBZ-REEL 功能描述:IC AMP AUD 2X2W STER D 16WLCSP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:D 類 輸出類型:1-通道(單聲道),帶立體聲耳機 在某負載時最大輸出功率 x 通道數量:930mW x 1 @ 8 歐姆; 40mW x 2 @ 16 歐姆 電源電壓:2.7 V ~ 5.5 V 特點:消除爆音,差分輸入,I²C,靜音,關閉,音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP(2.09x2.09) 封裝/外殼:25-WFBGA,WLCSP 包裝:帶卷 (TR) 其它名稱:MAX97000EWA+T-ND
SSM2380CBZ-REEL7 功能描述:IC AMP AUD 2X2W STER D 16WLCSP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:D 類 輸出類型:1-通道(單聲道),帶立體聲耳機 在某負載時最大輸出功率 x 通道數量:930mW x 1 @ 8 歐姆; 40mW x 2 @ 16 歐姆 電源電壓:2.7 V ~ 5.5 V 特點:消除爆音,差分輸入,I²C,靜音,關閉,音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP(2.09x2.09) 封裝/外殼:25-WFBGA,WLCSP 包裝:帶卷 (TR) 其它名稱:MAX97000EWA+T-ND
SSM23LPT 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SURFACE MOUNT SCHOTTKY BARRIER RECTIFIER VOLTAGE RANGE 20 - 40 Volts CURRENT 2.0 Amperes