參數資料
型號： ST16C452CJ68-F
廠商： Exar Corporation
文件頁數： 4/30頁
文件大?。?/td> 0K
描述： IC UART W/PAR PORT DUAL 68PLCC
標準包裝： 19
特點： *
通道數： 2，DUART
FIFO's： 1 字節
規程： 打印機
電源電壓： 2.97 V ~ 5.5 V
帶并行端口： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 68-LCC（J 形引線）
供應商設備封裝： 68-PLCC
包裝： 管件
其它名稱： ST16C452CJ68-F-ND
12
ST16C452/452PS
Rev. 3.20
used to strobe PD0-PD7 bus data into a printer input
buffer. -SLCTIN normally selects the printer while
AutoFDXT signals the printer to auto-linefeed. Other
signals provide similar printer functions but are not bi-
directional. The printer functions for these signals are
described in table 1, Symbol Description.
The interface provides a mode steering signal called
BIDEN. BIDEN controls the bi-directional 8-bit data
bus (PD0-PD7) direction, input or output. This pin
controls the port direction in the ST16C452. A logic 0 on
this pin places the parallel port in the output mode and
a logic 1 places the parallel port in the input mode. In the
ST16C452PS, the port direction is determined as de-
scribed in Table 6. When BIDEN is a logic 1 a single
control bit (D5) in the control register sets the input or
output mode. Setting BIDEN to a logic 0 however sets
an IBM interface compatible mode. In this mode the bus
direction (input/output) is set by eight data bits in the
IOSEL register. An AA (Hex) pattern sets the input
mode while a 55 (hex) pattern sets the output mode. I/
O direction is depicted in Table 6 below.
Printer Port
The 452/452PS contains a general purpose 8-bit
parallel interface port that is designed to directly
interface with a CENTRONICS Printer. A number of
the control/interrupt signals and the 8-bit data bus
have been designed as bi-directional data buses. This
allows the interface to function with other device
parallel data bus applications. Signal -ACK is used to
generate an -INTP interface interrupt that would nor-
mally be connected to the user CPU. -INTP can be
made to follow the -ACK signal, normal mode (see
Figure 7) or it can be configured for the latch mode. In
the latch mode the interrupt is not cleared until printer
status register (SR) is read. Another signal (INIT) can
be made to function as an outgoing or incoming
interrupt, or combined with other interrupts to provide
a common wire-or interrupt output. Interface signals -
STROBE, -AutoFDXT, and -SLCTIN are bi-direc-
tional and can be used as combinations of input and/
or output functions. The signals have internal pull-up
resistors and can be wire-or’d. Normally, -STROBE is
Table 6, PD0-PD7 I/O DIRECTION MODE SELECTION [452PS only]
PORT DIRECTION
BIDEN
CONTROL REGISTER (D5)
I/O SELECT REGISTER
Input mode
0
X (Note 4)
AA Hex
Output mode
0
X (Note 4)
55 Hex
Output mode
1
0
X (Note 4)
Input mode
1
X (Note 4)
Note: 4 = don’t care
相關PDF資料
PDF描述
XR16L2750CJ-F IC UART FIFO 64B DUAL 44PLCC
ST16C452IJ68PS-F IC UART W/PAR PORT DUAL 68PLCC
XR16V2651IL-F IC UART FIFO 32B DUAL 32QFN
XR16M2651IL32-F IC UART FIFO 32B DUAL 32QFN
XR88C192IVTR-F IC UART FIFO DUAL 44LQFP
相關代理商/技術參數
參數描述
ST16C452CJ68PS 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述:
ST16C452CJ68PS-F 功能描述:UART 接口集成電路 DUAL UART W/PARALEL PRINTER PORT RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
ST16C452CJ68TR-F 功能描述:UART 接口集成電路 DUAL UART W/PARALEL PRINTER PORT RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
ST16C452IJ68 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述:
ST16C452IJ68-F 功能描述:UART 接口集成電路 DUAL UART W/PARALEL PRINTER PORT RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*