參數資料
型號： ST62T08CM6
英文描述： IC-SM-8-BIT MCU 1K OTP
中文描述： 集成電路釤8位微控制器一千檢察官辦公室
文件頁數： 7/82頁
文件大小： 870K
代理商： ST62T08CM6
7/82
ST62T18C/E18C
1.2 PIN DESCRIPTIONS
V
and V
. Power is supplied to the MCU via
these two pins. V
is the power connection and
V
SS
is the ground connection.
OSCin and OSCout.
These pins are internally
connected to the on-chip oscillator circuit. A quartz
crystal, a ceramic resonator or an external clock
signal can be connected between these two pins.
The OSCin pin is the input pin, the OSCout pin is
the output pin.
RESET
. The active-low RESET pin is used to re-
start the microcontroller.
TEST/V
.
The TEST must be held at V
for nor-
mal operation. If TEST pin is connected to a
+12.5V level during the reset phase, the EPROM/
OTP programming Mode is entered.
NMI.
The NMI pin provides the capability for asyn-
chronous interruption, by applying an external non
maskable interrupt to the MCU. Schmitt trigger
characteristics. The user can select as option the
availability of an on-chip pull-up at this pin.
PA1-PA5.
These 5 lines are organised as one I/O
port (A). Each line may be configured under soft-
ware control as inputs with or without internal pull-
up resistors, input with interrupt generation and
pull-up resistor, open-drain or push-pull outputs.
PA3/ARTIMout and PA4/ARTIMin can be used re-
spectively as output and input pins for the embed-
ded 8-bit Auto-Reload Timer.
In addition,
PA1-PA5
can sink 20mA for direct LED
or TRIAC drive.
PB4...PB6.
These 3 lines are organised as one I/O
port (B). Each line may be configured under soft-
ware control as inputs with or without internal pull-
up resistors, input with interrupt generation and
pull-up resistor, open-drain or push-pull outputs,
analog inputs for the A/D converter.
PD4...PD7
. These 4 lines are organised as one I/O
port (portD). Each line may be configured under
software control as input with or without internal
pull-up resistor, input with interrupt generation and
pull-up resistor, analog input open-drain or push-
pull output. In addition, the pins PD5/TXD1 and
PD4/RXD1 can be used as UART output (PD5/
TXD1) or UART input (PD4/RXD1).
TIMER
. This is the TIMER 1 I/O pin. In input mode,
it is connected to the prescaler and acts as ex-
ternal timer clock or as control gate for the internal
timer clock. In output mode, the TIMER pin outputs
the data bit when a time-out occurs.The user can
select as option the availability of an on-chip pull-
up at this pin.
7
相關PDF資料
PDF描述
ST62T15BB6 8-BIT MICROCONTROLLER
ST62T15BM6 8-BIT MICROCONTROLLER
ST62T15CM6 MICROCONTROLLER|8-BIT|ST6200 CPU|CMOS|SOP|28PIN|PLASTIC
ST62T18CB3 8-BIT MICROCONTROLLER ( MCU ) WITH OTP. ROM. FASTROM. A/D CONVERTER. 8-BIT AUTO-RELOAD TIMER. UART. OSG. SAFE RESET AND 20 PINS
ST62T18CB6 8-BIT MICROCONTROLLER
相關代理商/技術參數
參數描述
ST62T09CB6 功能描述:8位微控制器 -MCU OTP EPROM 1K No Intf RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ST62T09CB6 制造商:STMicroelectronics 功能描述:IC 8BIT MCU OTP 2K 62T09 DIP20
ST62T09CM6 功能描述:8位微控制器 -MCU OTP EPROM 1K No Intf RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ST62T10CB6 功能描述:8位微控制器 -MCU OTP EPROM 2K No Intf RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ST62T10CB6 制造商:STMicroelectronics 功能描述:IC 8-BIT MCU OTP 2K
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*