參數資料
| 型號： | ST78C34CJ44-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 16/21頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART FIFO 83B 44PLCC |
| 標準包裝： | 27 |
| 特點： | * |
| FIFO's： | 83 字節 |
| 規程： | 打印機 |
| 電源電壓： | 5V |
| 帶并行端口： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 44-LCC（J 形引線） |
| 供應商設備封裝： | 44-PLCC（16.59x16.59） |
| 包裝： | 管件 |
6-6
ST78C34
Rev. 3.00
SYMBOL DESCRIPTION
Symbol
Pin
Signal
Pin Description
40
44
type
-ERROR
1
I
General purpose input or line printer error (active low, with internal
pull-up). This is an output from the printer to indicate an error by
holding it low during error condition.
SLCT
2
I
General purpose input or line printer selected (active high, with
internal pull-up). This is an output from the printer to indicate that
the line printer has been selected.
BUSY
3
I
General purpose input or line printer busy (active high, with internal
pull-up). An output from the printer to indicate printer is not ready
to accept data.
-ACK
4
I
General purpose input or line printer acknowledge (active low, with
internal pull-up). An output from the printer to indicate that data has
been accepted successfully.
PE
5
I
General purpose input or line printer paper empty (active high, with
internal pull-up). An output from the printer to indicate out of paper.
INTSEL
6
8
I
Interrupt select mode. The external -ACK can be selected as an
interrupt source by connecting this pin to the VCC or left open.
Connecting this pin to GND will set the interrupt to latched mode,
reading the status register resets the INT output.
D0-D7
14-7
16-9
I/O
Bi-directional data bus. Eight bit, three state data bus to transfer
information to or from the CPU. D0 is the least significant bit of
the data bus.
INT
16
19
O
Interrupt output (selectable active low or high). To signal the state
of the printer port. This pin tracks the -ACK input pin, When -ACK
is low INT is low and when -ACK is high INT is high if selected as
active low interrupt.
XTAL1
17
20
I
Crystal input 1 or external clock input. A crystal can be connected
to this pin and XTAL2 pin to utilize the internal oscillator circuit. An
external clock can be used to clock oscillator circuit.
XTAL2
18
21
O
Crystal input 2 or buffered clock output. See XTAL1.
-CS
19
22
I
Chip select (active low). A low at this pin enables the ST78C34 /
CPU data transfer operation.
相關PDF資料 |
PDF描述 |
|---|---|
| ST78C36ACJ44-F | IC UART FIFO 16B 44PLCC |
| SW06GSZ-REEL | IC SWITCH QUAD SPST 16SOIC |
| SX1501I087TRT | IC GPIO EXPANDER I2C 4CH 20QFN |
| SX1504I087TRT | IC GPIO EXPANDER I2C 4CH 20QFN |
| SX1509BULTRT | IC GPIO EXPANDER I2C 16CH 28QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST78C34CJ44TR-F | 制造商:Exar Corporation 功能描述:ST78C34CJ44TR-F |
| ST78C34CP40 | 功能描述:輸入/輸出控制器接口集成電路 Gen Purpose Parallel Printer Port RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| ST78C34CP40-F | 功能描述:輸入/輸出控制器接口集成電路 INTERNAL FIFO UART RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| ST78C34IJ44 | 制造商:EXAR 制造商全稱:EXAR 功能描述:GENERAL PURPOSE PARALLEL PRINTER PORT WITH 83 BYTE FIFO |
| ST78C34IP40 | 制造商:EXAR 制造商全稱:EXAR 功能描述:GENERAL PURPOSE PARALLEL PRINTER PORT WITH 83 BYTE FIFO |
發布緊急采購，3分鐘左右您將得到回復。