- 您現在的位置：買賣IC網 > PDF目錄383839 > ST78C34CJ44 (EXAR CORP) GENERAL PURPOSE PARALLEL PRINTER PORT WITH 83 BYTE FIFO PDF資料下載
參數資料
| 型號： | ST78C34CJ44 |
| 廠商： | EXAR CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | GENERAL PURPOSE PARALLEL PRINTER PORT WITH 83 BYTE FIFO |
| 中文描述： | 8 I/O, PIA-PRINTER INTERFACE, PQCC44 |
| 封裝： | PLASTIC, LCC-44 |
| 文件頁數： | 5/21頁 |
| 文件大?。?/td> | 198K |
| 代理商： | ST78C34CJ44 |
6-7
ST78C34
Rev. 3.00
SYMBOL DESCRIPTION
Symbol
Pin
Signal
type
Pin Description
40
44
GND
20
23
O
Signal and power ground.
RESET
21
24
I
Master reset (active high). A high on this pin will reset all the
outputs and internal registers.
-STROBE
22
25
I/O
General purpose I/O or strobe output (open drain active low, with
internal pull-up). To transfer latched data to the external peripheral
or printer.
-AUTOFDXT
23
26
I/O
General purpose I/O or line printer auto feed (open drain active
low, with internal pull-up). To signal the printer for continuous form
feed.
INIT
24
27
I/O
General purpose I/O or line printer initialize (open drain active
high, with internal pull-up). To signal the line printer to enter
internal initialization routine.
-SLCTIN
25
28
I/O
General purpose I/O or line printer select (open drain active low,
with internal pull-up). To select the line printer.
GND
26
30
O
Power and signal ground.
PD0-PD7
27-34
31-38
I/O
Bi-directional parallel ports (three state). To transfer data in or out
of the ST78C34 parallel port. PD7-PD0 are latched during output
mode.
A0-A1
36-37
40-41
I
Address lines. To select internal registers.
-IOW
38
42
I
Write strobe (active low). A low on this pin will transfer the contents
of the CPU data bus to the addressed register.
-IOR
39
43
I
Read strobe (active low). A low level on this pin transfers the
contents of the ST78C34 data bus to the CPU.
VCC
40
44
I
Power supply input.
相關PDF資料 |
PDF描述 |
|---|---|
| ST78C34CP40 | GENERAL PURPOSE PARALLEL PRINTER PORT WITH 83 BYTE FIFO |
| ST78C34IJ44 | GENERAL PURPOSE PARALLEL PRINTER PORT WITH 83 BYTE FIFO |
| ST78C34IP40 | GENERAL PURPOSE PARALLEL PRINTER PORT WITH 83 BYTE FIFO |
| ST78C36 | ECP/EPP Parallel Printer Port with 16 Byte FIFO(ECP/EPP并行打印機端口（帶16字節先進先出）) |
| ST78C36A | ECP/EPP Parallel Printer Port with 16 Byte FIFO(ECP/EPP并行打印機端口（帶16字節先進先出）) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST78C34CJ44-F | 功能描述:輸入/輸出控制器接口集成電路 INTERNAL FIFO UART RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| ST78C34CJ44TR-F | 制造商:Exar Corporation 功能描述:ST78C34CJ44TR-F |
| ST78C34CP40 | 功能描述:輸入/輸出控制器接口集成電路 Gen Purpose Parallel Printer Port RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| ST78C34CP40-F | 功能描述:輸入/輸出控制器接口集成電路 INTERNAL FIFO UART RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| ST78C34IJ44 | 制造商:EXAR 制造商全稱:EXAR 功能描述:GENERAL PURPOSE PARALLEL PRINTER PORT WITH 83 BYTE FIFO |
發布緊急采購，3分鐘左右您將得到回復。