SW06
REV. A
–3–
ELECTRICAL CHARACTERISTICS
SW06B
SW06F
SW06G
Parameter
Symbol
Conditions
Min Typ Max
Units
TEMPERATURE RANGE
TA
Operating
–55
+125
–25
+85
0
70
°C
“ON” RESISTANCE
RON
VS = 0 V, IS = 1.0 mA
75
110
75
125
75
175
VS = ± 10 V, IS = 1.0 mA
80
110
80
125
80
175
R
ON MATCH BETWEEN SWITCHES
RON Match
VS = 0 V, IS = 100 A
1
6
20
6
25
10
%
ANALOG VOLTAGE RANGE
VA
IS = 1.0 mA
2
+10 +11
+10
+11
V
IS = 1.0 mA
2
–10
–15
–10
–15
–10
–15
ANALOG CURRENT RANGE
IA
VS = ± 10 V
7
12
5
11
mA
R
ON WITH APPLIED VOLTAGE
R
ON
–10 V
≤ V
S ≤ 10 V, IS = 1.0 mA
10
12
15
%
SOURCE CURRENT IN
VS = 10 V, VD = –10 V
“OFF” CONDITION
IS(OFF)
TA = Max Operating Temp
3, 9
60
30
60
nA
DRAIN CURRENT IN
VS = 10 V, VD = –10 V
“OFF” CONDITION
ID(OFF)
TA = Max Operating Temp
3, 9
60
30
60
nA
LEAKAGE CURRENT IN
IS(ON)+
VS = VD = ± 10 V
100
30
60
nA
“ON” CONDITION
ID(ON)
TA = Max Operating Temp
3, 9
LOGICAL “1” INPUT CURRENT
IINH
VIN = 2.0 V to 15.0 V
5
10
15
A
LOGICAL “0” INPUT CURRENT
IINL
VIN = 0.8 V
4
10
4
10
5
15
A
TURN-ON TIME
tON
See Switching Time
440
900
500 900
1000
ns
Test Circuit
4, 8
TURN-OFF TIME
tOFF
See Switching Time
300
500
330 500
500
ns
Test Circuit
4, 8
BREAK-BEFORE-MAKE TIME
tON–tOFF
Note 7
70
50
ns
POSITIVE SUPPLY CURRENT
I+
All Channels “OFF,”
9.0
13.5
mA
DIS = “0”
3
NEGATIVE SUPPLY CURRENT
I–
All Channels “OFF,”
7.5
10.5
mA
DIS = “0”3
GROUND CURRENT
IG
All Channels “ON” or
6.0
7.5
mA
“OFF”
3
NOTES
(@ V+ = +15 V, V– = –15 V, –55 C
≤ T
A
≤ +125 C for SW06BQ, –40 C ≤ T
A
≤ +85 C for
SW06FQ and –40 C
≤ T
A
≤ +85 C for SW06GP/GS, unless otherwise noted)
1V
S = 0 V, IS = 100 A. Specified as a percentage of R AVERAGE where: RAVERAGE =
R
ON1 + RON 2 + RON 3 + RON 4
4
.
2Guaranteed by R
ON and leakage tests. For normal operation maximum analog signal voltages should be restricted to less than (V+) –4 V.
3Switch being tested ON or OFF as indicated, V
INH = 2.0 V or VINL = 0.8 V, per logic truth table.
4Also applies to disable pin.
5Current tested at V
IN = 2.0 V. This is worst case condition.
6Sample tested.
7Switch is guaranteed by design to provide break-before-make operation.
8Guaranteed by design.
9Parameter tested only at T
A = +125°C for military grade device.
Specifications subject to change without notice.