- 您現在的位置：買賣IC網 > PDF目錄1970 > SX1504I087TRT (Semtech)IC GPIO EXPANDER I2C 4CH 20QFN PDF資料下載
參數資料
| 型號： | SX1504I087TRT |
| 廠商： | Semtech |
| 文件頁數： | 6/31頁 |
| 文件大小： | 0K |
| 描述： | IC GPIO EXPANDER I2C 4CH 20QFN |
| 產品培訓模塊： | Low Voltage GPIO Expander Family |
| 標準包裝： | 1 |
| 接口： | I²C |
| 輸入/輸出數： | 4 |
| 中斷輸出： | 是 |
| 頻率 - 時鐘： | 400kHz |
| 電源電壓： | 2.5 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-UFQFN 裸露焊盤 |
| 供應商設備封裝： | 20-QFN-UT（3x3） |
| 包裝： | 標準包裝 |
| 產品目錄頁面： | 1359 (CN2011-ZH PDF) |
| 其它名稱： | SX1504I087DKR |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
WIRELESS & SENSING
Rev 3 – 16
th May 2012
www.semtech.com
14
SX1504/SX1505/SX1506
4/8/16 Channel GPIO
3.
In operation, the SX1504, SX1505 and SX1506 may be reset at anytime by an external device driving
NRESET low during tPULSE. Chip can be accessed normally again after NRESET rising edge.
4.
During a brown-out event, if VDDM drops above VDROPH a reset will not occur.
5.
During a brown-out event, if VDDM drops between VDROPH and VDROPL a reset may occur.
6.
During a brown-out event, if VDDM drops below VDROPL a reset will occur next time VPOR is crossed.
Please note that a brown-out event is defined as a transient event on VDDM. If VDDM is attached to a battery,
then the gradual decay of the battery voltage will not be interpreted as a brown-out event.
Please also note that a sharp rise in VDDM (> 1V/us) may induce a circuit reset.
4.5
2-Wire Interface (I
2C)
The SX1504, SX1505 and SX1506 2-wire interface (I
2C compliant) operates only in slave mode. In this
configuration, the device has one or two device addresses defined by ADDR pin.
Device
ADDR Pin
I
2C Address
Description
0
0x20 (0100000)
First address of the 2-wire interface
SX1504 &
SX1505
1
0x21 (0100001)
Second address of the 2-wire interface
SX1506
0x20 (0100000)
Fixed address of the 2-wire interface
Table 6 - 2-Wire Interface Address
2 lines are used to exchange data between an external master host and the slave device:
SCL : Serial CLock
SDA : Serial DAta
The SX1504, SX1505 and SX1506 are read-write slave-mode I
2C devices and comply with the Philips I2C
standard Version 2.1 dated January, 2000. The SX1504, SX1505 and SX1506 have respectively 12, 16, and 31
user-accessible internal 8-bit registers. The I
2C interface has been designed for program flexibility, in that once
the slave address has been sent to the SX1504, SX1505 or SX1506 enabling it to be a slave
transmitter/receiver, any register can be written or read independently of each other. While there is no auto
increment/decrement capability in the SX1504 and SX1505 I
2C logic, a tight software loop can be designed to
access the next register independent of which register you begin accessing. SX1506 implements auto increment
capability. The start and stop commands frame the data-packet and the repeat start condition is allowed if
necessary.
Seven bit addressing is used and ten bit addressing is not allowed. Any general call address will be ignored by
the SX1504, SX1505 and SX1506. The SX1504, SX1505 and SX1506 are not CBUS compatible and can
operate in standard mode (100kbit/s) or fast mode (400kbit/s).
4.5.1
WRITE
The simplest format for an I
2C write is given below. After the start condition [S], the slave address is sent,
followed by an eighth bit indicating a write. The I
2C then acknowledges that it is being addressed, and the master
responds with an 8 bit data byte consisting of the register address. The slave acknowledges and the master
sends the appropriate 8 bit data byte. Once again the slave acknowledges and the master terminates the
transfer with the stop condition [P].
Master operations
SX1504, SX1505 or SX1506 operations (Slave)
S: Start Condition
Slave Address: 7 bit
W: Write = ‘0’
Register Address: 8 bit
A: Acknowledge (sent by slave)
Data: 8 bit
P: Stop condition
Figure 8 - 2-Wire Serial Interface, Write Register Operation
相關PDF資料 |
PDF描述 |
|---|---|
| SX1509BULTRT | IC GPIO EXPANDER I2C 16CH 28QFN |
| SX8722I070TRLF | IC ZOOMING ADC 10BIT 16CH 44MLPQ |
| SX8723CWLTDT | IC DAS ADC 16BIT I2C/SRL |
| SX8723E083TDT | IC DAS PRESS/TEMP SENS 12MLPD |
| SX8724CWLTDT | IC DAS ADC 16BIT I2C/SRL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SX1504I088TRT | 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:4/8/16 Channel GPIO with NINT and NRESET |
| SX1505I087TRT | 功能描述:IC GPIO EXP I2C 8CH 20UTQFN RoHS:是 類別:集成電路 (IC) >> 接口 - I/O 擴展器 系列:- 產品培訓模塊:I²C Bus Fundamentals 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 接口:I²C，SM 總線 輸入/輸出數:16 中斷輸出:是 頻率 - 時鐘:400kHz 電源電壓:2.3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:24-TSSOP 包裝:Digi-Reel® 包括:POR 產品目錄頁面:826 (CN2011-ZH PDF) 配用:568-4002-ND - DEMO BOARD I2C 其它名稱:568-1058-6 |
| SX1505I088TRT | 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:4/8/16 Channel GPIO with NINT and NRESET |
| SX1506I089TRT | 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:4/8/16 Channel GPIO with NINT and NRESET |
| SX1506I091TRT | 功能描述:IC GPIO EXP I2C 16CH 28UTQFN RoHS:是 類別:集成電路 (IC) >> 接口 - I/O 擴展器 系列:- 產品培訓模塊:I²C Bus Fundamentals 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 接口:I²C，SM 總線 輸入/輸出數:16 中斷輸出:是 頻率 - 時鐘:400kHz 電源電壓:2.3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:24-TSSOP 包裝:Digi-Reel® 包括:POR 產品目錄頁面:826 (CN2011-ZH PDF) 配用:568-4002-ND - DEMO BOARD I2C 其它名稱:568-1058-6 |
發布緊急采購，3分鐘左右您將得到回復。