- 您現在的位置：買賣IC網 > PDF目錄372394 > SX28AC75DP IC-8-BIT MCU PDF資料下載
參數資料
| 型號： | SX28AC75DP |
| 英文描述： | IC-8-BIT MCU |
| 中文描述： | 集成電路8位微控制器 |
| 文件頁數： | 17/42頁 |
| 文件大?。?/td> | 312K |
| 代理商： | SX28AC75DP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
1999 Scenix Semiconductor, Inc. All rights reserved.
- 17 -
www.scenix.com
SX18AC / SX20AC / SX28AC
7.2
The WKPND_B register comes up with a random value
upon reset. The user program must clear the register
prior to enabling the wake-up condition or interrupts. The
proper initialization sequence is:
1. Select the desired edge (through WKED_B register)
2. Clear the WKPND_B register
3. Enable the Wakeup condition (through WKEN_B regis-
ter)
Below is an example of how to read the WKPND_B regis-
ter to determine which Port B pin caused the wakeup or
interrupt, and to clear the WKPND_B register:
Port B MIWU/Interrupt Configuration
The final “mov” instruction in this example performs an
exchange of data between the working register (W) and
the WKPND_B register. This exchange occurs only with
Port B accesses. Otherwise, the “mov” instruction does
not perform an exchange, but only moves data from the
source to the destination.
Here is an example of a program segment that config-
ures the RB0, RB1, and RB2 pins to operate as Multi-
Input Wakeup/Interrupt pins, sensitive to falling edges:
To prevent false interrupts, the enabling step (clearing
bits in WKEN_B) should be done as the last step in a
sequence of Port B configuration steps. After this pro-
gram segment is executed, the device can receive inter-
rupts on the RB0, RB1, and RB2 pins. If the device is put
into the power down mode (by executing the SLEEP
instruction), the device can then receive wakeup signals
on those same pins.
mov
clr
mov
M,#$09
W
!RB,W
;W contains WKPND_B
;contents of W exchanged
;with contents of WKPND_B
mov M,#$0F
;prepare to write port data
;direction registers
;load W with the value 07h
;configure RB0-RB2 to be inputs
mov W,#$07
mov !RB,W
mov M,#$0A
;prepare to write WKED_B
;(edge) register
;W contains the value 07h
;configure RB0-RB2 to sense
;falling edges
;prepare to access WKPND_B
;(pending) register
;clear W
;clear all wakeup pending bits
mov !RB,W
mov M,#$09
mov W,#$00
mov !RB,W
mov M,#$0B
;prepare to write WKEN_B (enable)
;register
mov W,#$F8h ;load W with the value F8h
mov !RB,W
;enable RB0-RB2 to operate as
;wakeup inputs
相關PDF資料 |
PDF描述 |
|---|---|
| SX28AC75SO | IC-SM-8-BIT MCU |
| SX28ACDP | IC-8-BIT MCU |
| SX28ACSO | SX28ACSO:IC-SM-8-BIT MCU |
| SX18AC75DP | IC-8-BIT MCU |
| SX18AC75SO | IC-SM-8-BIT MCU |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SX28AC75-I/DP | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Configurable Communications Controllers with EE/Flash Program Memory, In-System Programming Capability and On-Chip Debug |
| SX28AC75-I/PQ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Configurable Communications Controllers with EE/Flash Program Memory, In-System Programming Capability and On-Chip Debug |
| SX28AC75-I/SO | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Configurable Communications Controllers with EE/Flash Program Memory, In-System Programming Capability and On-Chip Debug |
| SX28AC75-I/SS | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Configurable Communications Controllers with EE/Flash Program Memory, In-System Programming Capability and On-Chip Debug |
| SX28AC75-I/TQ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Configurable Communications Controllers with EE/Flash Program Memory, In-System Programming Capability and On-Chip Debug |
發布緊急采購，3分鐘左右您將得到回復。