- 您現在的位置：買賣IC網 > PDF目錄11211 > SY58040UMY TR (Micrel Inc)IC CROSSPOINT SWITCH 4X4 44MLF PDF資料下載
參數資料
| 型號： | SY58040UMY TR |
| 廠商： | Micrel Inc |
| 文件頁數： | 5/11頁 |
| 文件大小： | 0K |
| 描述： | IC CROSSPOINT SWITCH 4X4 44MLF |
| 標準包裝： | 1,000 |
| 系列： | Precision Edge® |
| 功能： | 交叉點開關 |
| 電路： | 1 x 4:4 |
| 電壓電源： | 單電源 |
| 電壓 - 電源，單路/雙路(±)： | 2.375 V ~ 2.625 V |
| 電流 - 電源： | 225mA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 44-VFQFN 裸露焊盤，44-MLF? |
| 供應商設備封裝： | 44-MLF?（7x7） |
| 包裝： | 帶卷 (TR) |
| 其它名稱： | SY58040UMYTR SY58040UMYTR-ND |
3
SY58040U
Micrel, Inc.
M9999-103009
hbwhelp@micrel.com or (408) 955-1690
PACkAGE/ORDERINGINFORMATION
OrderingInformation(1)
Package Operating
Package
PartNumber
Type
Range
Marking
SY58040UMY(3)
QFN-44
Industrial SY58040U Pb-Free
Pb-Free
bar-line indicator
SY58040UMYTR(2, 3) QFN-44
Industrial SY58040U Pb-Free
Pb-Free
bar-line indicator
Notes:
1. Contact factory for die availability. Dice are guaranteed at TA = 25°C, DC electricals only.
2. Tape and Reel.
3. Pb-Free package recommended for new designs.
PinNumber PinName
PinFunction
17, 15,
IN0, /IN0
Differential Inputs: These input pairs are the differential signal inputs to the device. Inputs accept
10, 8,
IN1, /IN1
AC or DC-coupled signals as small as 100mV. Each pin of a pair internally terminates to a VT pin
4, 2,
IN2, /IN2
through 50. Note that these inputs will default to an indeterminate state if left open. Please refer to
41, 39
IN3, /IN3
the “Input Interface Applications” section for more details.
16, 9,
VT0, VT1
Input Termination Center-Tap: Each side of the differential input pair terminates to a VT pin. The VT
3, 40
VT2, VT3
pins provide a center-tap to a termination network for maximum interface flexibility. See “Input
Interface Applications” section for more details.
14,
VRef_AC0
Reference Voltage: This output biases to VCC–1.2V. It is used when AC coupling the inputs.
11,
VRef_AC1
Connect VRef-AC output pin to the VT input pin. Bypass each VRef-AC pin with a 0.01F low ESR
1,
VRef_AC2
capacitor to VCC. See “Input Interface Applications” section for more details.
42
VRef_AC3
18
SIN0
These single-ended TTL/CMOS-compatible inputs address the data inputs. Note that these inputs
19
SIN1
are internally connected to a 25k pull-up resistor and will default to a logic HIGH state if left open.
38
SOUT0
These single-ended TTL/CMOS-compatible inputs address the data outputs. Note that these inputs
37
SOUT1
are internally connected to a 25k pullup resistor and will default to a logic HIGH state if left open.
5
CONF,
These single-ended TTL/CMOS compatible inputs control the transfer of the addresses to the
7
LOAD
internal multiplexers. See “Address Tables” and “Timing Diagram” sections for more details. Note
that these inputs are internally connected to a 25k pull-up resistor and will default to a logic HIGH
state if left open.
Configuration Sequence
1. Load: Loads configuration into buffer, while Configuration Buffer holds existing switch configuration.
2. Configuration: Loads new configuration into the Configuration Buffer and updates switch configuration.
Buffer Mode
The SY58040U defaults to buffer mode (IN-to-Q) if the load and configuration control signals are floating.
23, 24,
Q0, /Q0,
Differential Outputs: These CML output pairs are the outputs of the device. Please refer to the truth
26, 27,
Q1, /Q1,
table below for details. Unused output pairs may be left open. Each output is designed to drive
29, 30
Q2, /Q2,
400mV into 100 across the pair, or 50 to VCC.
32, 33
Q3, /Q3,
6, 22, 25,
VCC
Positive power supply. Bypass with 0.1F//0.01F low ESR capacitors and place as close to each
28, 31, 34
VCC pin.
12, 13, 20, 21,
GND,
Ground. GND and EPad must both be connected to most negative potential of chip ground.
35, 36, 43, 44 Exposed pad
PIN DESCRIPTION
44-PinQFN(QFN-44)
相關PDF資料 |
PDF描述 |
|---|---|
| AD7510DIJP | IC SWITCH QUAD SPST 20PLCC |
| VI-JWB-IW | CONVERTER MOD DC/DC 95V 100W |
| SY58024UMG TR | IC CROSSPOINT SWITCH DUAL 32MLF |
| VI-JW4-IW | CONVERTER MOD DC/DC 48V 100W |
| ADG507AKP | IC MULTIPLEXER DUAL 8X1 28PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SY58051AUMG | 功能描述:Configurable Multiple Function Configurable 1 Circuit 2 Input 16-QFN (3x3) 制造商:microchip technology 系列:SY58 包裝:管件 零件狀態:有效 邏輯類型:可配置多功能 電路數:1 輸入數:2 施密特觸發器輸入:無 輸出類型:差分 電流 - 輸出高，低:- 電壓 - 電源:2.5 V ~ 3.3 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-VFQFN 裸露焊盤 供應商器件封裝:16-QFN（3x3） 標準包裝:100 |
| SY58051U | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:Ultra-Precision CML AnyGate ? with Internal Input and Output Termination |
| SY58051U_11 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:Ultra-Precision CML AnyGate ? with Internal Input and Output Termination |
| SY58051UMG | 功能描述:邏輯門 10Gbps CML AnyGate (I Temp, Green) RoHS:否 制造商:Texas Instruments 產品:OR 邏輯系列:LVC 柵極數量:2 線路數量（輸入/輸出）:2 / 1 高電平輸出電流:- 16 mA 低電平輸出電流:16 mA 傳播延遲時間:3.8 ns 電源電壓-最大:5.5 V 電源電壓-最小:1.65 V 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:DCU-8 封裝:Reel |
| SY58051UMG TR | 功能描述:邏輯門 10Gbps CML AnyGate (I Temp, Green) RoHS:否 制造商:Texas Instruments 產品:OR 邏輯系列:LVC 柵極數量:2 線路數量（輸入/輸出）:2 / 1 高電平輸出電流:- 16 mA 低電平輸出電流:16 mA 傳播延遲時間:3.8 ns 電源電壓-最大:5.5 V 電源電壓-最小:1.65 V 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:DCU-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。