參數資料
型號： SYNCMASTER753DF(DF17K*)
英文描述： Monitor_ICs:88P6232 TDA4859
中文描述： Monitor_ICs：88P6232 TDA4859
文件頁數： 4/65頁
文件大?。?/td> 1211K
1.
Servicing precautions are printed on the cabinet,
and should be followed closely.
Always unplug the unit’s AC power cord from the
AC power source before attempting to: (a) remove
or reinstall any component or assembly, (b)
disconnect PCB plugs or connectors, (c) connect all
test components in parallel with an electrolytic
capacitor.
Some components are raised above the printed
circuit board for safety. An insulation tube or tape
is sometimes used. The internal wiring is
sometimes clamped to prevent contact with
thermally hot components. Reinstall all such
elements to their original position.
4. After servicing, always check that the screws,
components and wiring have been correctly
reinstalled. Make sure that the area around the
serviced part has not been damaged.
2.
3.
1.
Immediately before handling any semiconductor
components or assemblies, drain the electrostatic
charge from your body by touching a known earth
ground. Alternatively, wear a discharging wrist-
strap device. To avoid a shock hazard, be sure to
remove the wrist strap before applying power to
the monitor.
After removing an ESD-equipped assembly, place it
on a conductive surface such as aluminum foil to
prevent accumulation of an electrostatic charge.
Do not use freon-propelled chemicals. These can
generate electrical charges sufficient to damage
ESDs.
Use only a grounded-tip soldering iron to solder or
desolder ESDs.
Use only an anti-static solder removal device. Some
solder removal devices not classified as “anti-static”
can generate electrical charges sufficient to damage
ESDs.
2.
3.
4.
5.
5.
Check the insulation between the blades of the AC
plug and accessible conductive parts (examples:
metal panels, input terminals and earphone jacks).
Insulation Checking Procedure: Disconnect the
power cord from the AC source and turn the power
switch ON. Connect an insulation resistance meter
(500 V) to the blades of the AC plug.
The insulation resistance between each blade of the
AC plug and accessible conductive parts (see
above) should be greater than 1 megohm.
Never defeat any of the +B voltage interlocks. Do
not apply AC power to the unit (or any of its
assemblies) unless all solid-state heat sinks are
correctly installed.
Always connect a test instrument’s ground lead to
the instrument chassis ground
before
connecting the
positive lead; always remove the instrument’s
ground lead last.
6.
7.
8.
6.
Do not remove a replacement ESD from its
protective package until you are ready to install it.
Most replacement ESDs are packaged with leads
that are electrically shorted together by conductive
foam, aluminum foil or other conductive materials.
Immediately before removing the protective
material from the leads of a replacement ESD,
touch the protective material to the chassis or
circuit assembly into which the device will be
installed.
Caution:
Be sure no power is applied to the
chassis or circuit and observe all
other safety precautions.
7.
8.
Minimize body motions when handling
unpackaged replacement ESDs. Motions such as
brushing clothes together, or lifting your foot from
a carpeted floor can generate enough static
electricity to damage an ESD.
Indicates ESDs on the Schematic Diagram in
this manual.
9.
1 Precautions
1-2
SyncMaster 753DF/755DF
1-3 Electrostatically Sensitive Devices (ESD) Precautions
Some semiconductor (solid state) devices can be easily damaged by static electricity. Such components are commonly
called Electrostatically Sensitive Devices (ESD). Examples of typical ESD devices are integrated circuits and some field-
effect transistors. The following techniques will reduce the incidence of component damage caused by static electricity.
1-2 Servicing Precautions
WARNING1: First read the “Safety Precautions” section of this manual. If unforeseen circumstances
create conflict between the servicing precautions and safety precautions, always
follow the safety precautions.
WARNING2: A high voltage VR replaced in the wrong direction may cause excessive X-ray
emissions.
WARNING3: An electrolytic capacitor installed with the wrong polarity might explode.
相關PDF資料
PDF描述
SYNCMASTER755DF(DF17J*) Monitor_ICs:88P6232 TDA4859
SYNCMASTER170T_180T Monitor_ICs:GS1881 AD9884AKS-140 416S1020B MTV121P-31 MX88L282FC 3P863
SYS161000FKX-10 x16 SRAM Module
SYS161000FKX-12 x16 SRAM Module
SYS161000FKX-70 x16 SRAM Module
相關代理商/技術參數
參數描述
SYNCMISC 制造商:Cypress Semiconductor 功能描述:USB - Bulk
SYN-PRO-WIN-USB-1YR 制造商:Microsemi Corporation 功能描述:SOFTWARE - Virtual or Non-Physical Inventory (Software & Literature)
SYNTEGRA CHASSIS NRE 制造商:Sliger Designs, Inc. 功能描述:SYNTEGRA CHASSIS NRE FOR SLIGER - Virtual or Non-Physical Inventory (Software & Literature)
SYOPT003 制造商:Schneider Electric 功能描述:APC SYMMETRA PX 250KW BATTERY BREAKER ENCLOSURE FUSE KIT 500 - Bulk 制造商:Schneider Electric 功能描述:APC Symmetra PX 250kW Battery Breaker Enclosure Fuse Kit 500A
SYOPT004 制造商:Schneider Electric 功能描述:APC SYMMETRA PX 500KW BATTERY BREAKER ENCLOSURE FUSE KIT 100 - Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*