參數資料
型號: T5750
廠商: Atmel Corp.
英文描述: UHF ASK/FSK TRANSMITTER
中文描述: 超高頻ASK / FSK發射器
文件頁數: 5/12頁
文件大?。?/td> 212K
代理商: T5750
5
T5750 [Preliminary]
4546B–RKE–07/04
Output Matching and Power
Setting
The output power is set by the load impedance of the antenna. The maximum output
power is achieved with a load impedance of Z
Load,opt
= (166 + j226)
at 868.3 MHz.
There must be a low resistive path to V
S
to deliver the DC current.
The delivered current pulse of the power amplifier is 7.7 mA and the maximum output
power is delivered to a resistive load of 475
if the 0.53 pF output capacitance of the
power amplifier is compensated by the load impedance.
An optimum load impedance of:
Z
Load
= 475
|| j/(2
× π ×
f
×
0.53 pF) = (166 + j226)
thus results for the maximum out-
put power of 5.5 dBm.
The load impedance is defined as the impedance seen from the T5750’s ANT1, ANT2
into the matching network. Do not confuse this large signal load impedance with a small
signal input impedance delivered as input characteristic of RF amplifiers and measured
from the application into the IC instead of from the IC into the application for a power
amplifier.
Less output power is achieved by lowering the real parallel part of 475
where the
parallel imaginary part should be kept constant.
Output power measurement can be done with the circuit of Figure 5. Note that the com-
ponent values must be changed to compensate the individual board parasitics until the
T5750 has the right load impedance Z
Load,opt
= (166 + j226)
at 868.3 MHz. Also the
damping of the cable used to measure the output power must be calibrated out.
Figure 5.
Output Power Measurement
Application Circuit
For the supply-voltage blocking capacitor C
3
a value of 68 nF/X7R is recommended
(see Figure 6 on page 6 and Figure 7 on page 7). C
1
and C
2
are used to match the loop
antenna to the power amplifier where C
1
typically is 3.9 pF/NP0 and C
2
is 1 pF/NP0; for
C
2
two capacitors in series should be used to achieve a better tolerance value and to
have the possibility to realize the Z
Load,opt
by using standard valued capacitors.
C
1
forms together with the pins of T5750 and the PCB board wires a series resonance
loop that suppresses the 1
st
harmonic, hence the position of C
1
on the PCB is important.
Normally the best suppression is achieved when C
1
is placed as close as possible to the
Pins ANT1 and ANT2.
The loop antenna should not exceed a width of 1.5 mm, otherwise the Q-factor of the
loop antenna is too high.
L
1
(
50 nH to 100 nH) can be printed on PCB. C
4
should be selected so that the XTO
runs on the load resonance frequency of the crystal. Normally, a value of 12 pF results
for a 15 pF load-capacitance crystal.
~
~
ANT2
ANT1
Rin
50
Power
meter
L
1
= 10n
C
2
= 1.5p
Z
Lopt
V
S
Z = 50
C
1
= 1n
3
C = 2.7p
相關PDF資料
PDF描述
T5750-6AQ UHF ASK/FSK TRANSMITTER
T5753 UHF ASK/FSK TRANSMITTER
T5753-6AQ UHF ASK/FSK TRANSMITTER
T5754 UHF ASK/FSK TRANSMITTER
T5754-6AQ UHF ASK/FSK TRANSMITTER
相關代理商/技術參數
參數描述
T5750_07 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:UHF ASK/FSK Transmitter
T5750-6AP 功能描述:IC TX 868-928MHZ ASK/FSK 8-TSSOP RoHS:否 類別:RF/IF 和 RFID >> RF 發射器 系列:- 標準包裝:4,000 系列:- 頻率:310MHz ~ 440MHz 應用:- 調制或協議:UHF,ASK 數據傳輸率 - 最大:20 kBaud 功率 - 輸出:1dBm ~ 5dBm 電流 - 傳輸:10mA 數據接口:PCB,表面貼裝 天線連接器:PCB,表面貼裝 存儲容量:- 特點:- 電源電壓:2.2 V ~ 4 V 工作溫度:-40°C ~ 85°C 封裝/外殼:16-LSSOP(0.154",3.90mm 寬) 包裝:帶卷 (TR)
T5750-6AQ 功能描述:IC TX 868-928MHZ ASK/FSK 8TSSOP RoHS:否 類別:RF/IF 和 RFID >> RF 發射器 系列:- 標準包裝:4,000 系列:- 頻率:310MHz ~ 440MHz 應用:- 調制或協議:UHF,ASK 數據傳輸率 - 最大:20 kBaud 功率 - 輸出:1dBm ~ 5dBm 電流 - 傳輸:10mA 數據接口:PCB,表面貼裝 天線連接器:PCB,表面貼裝 存儲容量:- 特點:- 電源電壓:2.2 V ~ 4 V 工作溫度:-40°C ~ 85°C 封裝/外殼:16-LSSOP(0.154",3.90mm 寬) 包裝:帶卷 (TR)
T5750-6AQJ 功能描述:射頻發射器 ASK/FSK Transmitter 868 - 928 MHz RoHS:否 制造商:Micrel 類型:ASK Transmitter 封裝 / 箱體:SOT-23-6 工作頻率:300 MHz to 450 MHz 封裝:Reel
T5750-6AQJ 71 制造商:Atmel Corporation 功能描述:UHF ASK/FSK TRANSMITTER